Results 171 to 180 of about 38,153 (263)

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Numerical Simulations of Strength Characteristics of Lightweight Fibre-Reinforced Concrete. [PDF]

Materials (Basel)
Michalik A, Gołębiowski Ł, Chyliński F.   +2 more
europepmc   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Irradiation Damage Behavior and Mechanism of Pressureless-Sintered ZrC Ceramics. [PDF]

Materials (Basel)
Ma J, Wu H, Liu H, Yang Y, Liu Z, Wu X, Pei B, Han J, Wang C, Huang Z.   +9 more
europepmc   +1 more source

In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy

Advanced Engineering Materials, EarlyView.
A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal, Tae‐Hyeok Kang, Pyuck‐Pa Choi, Subin Lee, Christoph Kirchlechner   +4 more
wiley   +1 more source

High Frequency Surface Hardening (I)

The Journal of the Japan Institute of Metals.A, 1950
openaire   +3 more sources

AS7341 Spectral Sensor with Machine Learning for Non-Contact Temperature Monitoring in Electrolytic-Plasma Hardening. [PDF]

Sensors (Basel)
Kussainov R, Erboluly A, Bakyt Z, Kadyrbolat N, Kurmangaliyev R, Rakhadilov B, Koc V, Rakhmetollayeva A, Satbayeva Z.   +8 more
europepmc   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Energy transfer mechanism in ultrasonic impact and its single-cycle equivalent experimental methodology. [PDF]

Ultrason Sonochem
Jiang Q, Ran T, Lai Y, Lin P, Qian P, Xu Z, Sun F.   +6 more
europepmc   +1 more source

Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)

Advanced Engineering Materials, EarlyView.
Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho, M. Naeem, T. H. C. Costa, M. S. Libório, J. C. A. Queiroz, C. B. B. Luna, R. R. M. Sousa, P. S. Vieira, E. M. Araújo   +8 more
wiley   +1 more source