Results 191 to 200 of about 2,581,564 (248)

Validation of a Spatially Resolved Reflectance Imaging System for Recovery of <i>µ_a</i> and <i>µ_s</i>' in Absorbing Turbid Media. [PDF]

Sensors (Basel)
Jones ZD, Foschum F, Kienle A.
europepmc   +1 more source

Pain and Patient‐Reported Physical Function Did Not Differ Between Body Composition Profiles in Patients with Hip Osteoarthritis

Arthritis Care &Research, Accepted Article.
Objective To explore whether higher body fat and lower lean mass are associated with greater pain and worse patient‐reported physical function in individuals with hip osteoarthritis (OA). A secondary aim was to examine whether pain and patient‐reported physical function differ according to four body composition profiles: high body fat, low lean mass ...
Alexandra Ryan, Boliang Wang, Fiona Dobson, Ben Kirk, Travis Haber, Kim L. Bennell, Shirley P. Yu, Kim Allison, Ricardo J.S. Costa, Gabrielle Knox, Michelle Hall   +10 more
wiley   +1 more source

Hotspots of N2O accumulation in the soil profile of alternate wetting and drying paddy fields. [PDF]

Front Plant Sci
Liu G, Chen X, Chen T, Chi D, Zou H.
europepmc   +1 more source

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Can participative leadership and LMX congruence promote collective organizational engagement? [PDF]

PLoS One
Li M, Cao J, Sun Q.
europepmc   +1 more source

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

From Qualitative Localisation to Quantitative Verification: Integrating Active IR Thermography and Laser Scanning in Wind Turbine Blade Inspection. [PDF]

Materials (Basel)
Stawiarski A.
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Prediction and reduction of dynamic factor based on dynamic behavior of gear systems. [PDF]

Sci Rep
Lee D, Shim SB, Kim S.
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source