Results 221 to 230 of about 5,177,586 (301)

Highly Conductive and Transparent Coatings via Low‐Temperature Hydroiodic Acid Vapor Treatment of Oxo‐Graphene Thin Films

Advanced Materials Technologies, EarlyView.
The double self‐assembly (DSA) method applied to oxo‐graphene (oxo‐G) flakes followed by hydroiodic acid (HI) vapor treatment and low‐temperature annealing yields highly conductive, optically transparent thin films with the potential for applications in electronic and optoelectronic devices.
Arindam Konar, David Kaiser, Guobin Jia, Hamid Reza Rasouli, Janis Köster, Christof Neumann, Andrea Dellith, Uwe Hübner, Christian E. Halbig, Siegfried Eigler, Ute Kaiser, Benjamin Dietzek‐Ivanšić, Jonathan Plentz, Andrey Turchanin   +13 more
wiley   +1 more source

3D‐Printed Actuator Powered by Liquid Crystal Elastomer Muscles at the Water–Air Interface

Advanced Materials Technologies, EarlyView.
Soft robots for unstructured environments require responsive, durable actuators. Liquid crystal elastomers (LCEs) provide large reversible deformations under thermal or optical stimuli. Direct ink writing enables fabrication of LCE actuators integrated with silicone, with mesogen chemistry and oligomers optimized for printable inks.
Cecilie Ryberg, Stefan Pendlmayr, Jan Skov Pedersen, Jens Vinge Nygaard, Jan P. F. Lagerwall, Brigitte Städler   +5 more
wiley   +1 more source

Extrusion‐Based Bioprinting of Living Bioinks for Tissue and Organ Engineering

Advanced Materials Technologies, EarlyView.
Extrusion‐based bioprinting is presented as the most versatile route for fabricating living, heterogeneous tissues. Its ability to combine diverse bioinks, support matrices, and advanced printhead geometries transforms familiar constraints into powerful biofabrication opportunities.
Eric Silberman, Ester Sapir Baruch, Roni Cohen, Assaf Shapira, Tal Dvir   +4 more
wiley   +1 more source

Chest tube fixation strength depends on suture caliber and fixation technique rather than tube diameter: a biomechanical cadaver study. [PDF]

Eur J Trauma Emerg Surg
Fricke JJ, Schöbel T, Meißner R, Schleifenbaum S, Kleber C, Metelmann I, Krämer S.   +6 more
europepmc   +1 more source

Autonomous Reconfigurable Modular Conductive Hydrogels for Adaptive and Degradable Bioelectronic Interfaces

Advanced Materials Technologies, EarlyView.
Bridging rigid electrodes with soft, irregular tissues demands more than conductivity alone. Modular conductive hydrogels autonomously reconfigure into conformal electrode‐tissue interfaces, coupling mixed ionic‐electronic conduction with tissue‐like mechanics, self‐healing, and degradability.
Matthew K. Burgess, Zofia B. Wolny, Zekun Liu, Karolina Cysewska, Malavika Nair   +4 more
wiley   +1 more source

Survival after cannula rupture in a fully VAD-dependent child-lessons in preparedness. [PDF]

JHLT Open
Khan S, Montgomery C, Mesce A, Caltabiano E, Wittlieb-Weber C, Lin K, Ahmed H, Naim M, O'Connor M, Melchior R, Rossano J, Maeda K, Edelson J.   +12 more
europepmc   +1 more source

Low‐Outgassing Liquid Metal–Silicone Composites for Multifunctional Space Applications

Advanced Materials Technologies, EarlyView.
Integrating liquid metal microdroplets into a space‐grade silicone creates a multifunctional composite while preserving its inherent flexibility and low‐outgassing behavior. The composite has 11×$\times$ higher thermal conductivity while remaining thermally stable and maintaining a total mass loss of ≤$\le$ 1% under thermal vacuum testing.
Spencer Pak, Matthew R. Jamison, Cadré J. Francis, Ravi Tutika, Stephen A. Morin, Eric J. Markvicka   +5 more
wiley   +1 more source

Bicornuate Uterus with Third Trimester Fetal Demise in a Non-Communicating Rudimentary Uterine Horn: A Case Report. [PDF]

Int Med Case Rep J
Innocent B, Warsame FD, Hashi Snr AH, Noor FA, Deheyeh MA, Omar Snr QI, Josephine N, Emmanuel O, Petrus B, Hakizimana T, Ebaid AAS.   +10 more
europepmc   +1 more source

Parameter Investigation for Stamp Manufacturing of Complex 3D Geometries Using Nanoimprint Lithography

Advanced Materials Technologies, EarlyView.
Nanoimprint lithography can replicate complex 3D microstructures with undercuts using single‐layer polymer stamps of different elasticities. By combining experiments and simulations, T‐shaped geometries and suitable undercut radii were identified that minimize stress and defects during demolding.
Christos Julianos Karapatzakis, Selina Burkert, Cordelia Friederike Wittemann, Andreas Heinrich   +3 more
wiley   +1 more source

Mechanism-constrained D-optimal design of a flexible claw for peanut shelling under biological variability. [PDF]

Front Plant Sci
Tuo Y, Pang Y, Zhao X, Li M, Zhang Y, Yu Z, Liang T, Zheng P, Chen Z, Sun Q, Bai X, Zhao Y.   +11 more
europepmc   +1 more source