Results 231 to 240 of about 406,042 (279)
Yeast-powered microfluidic pump based on a four-parameter fermentation model. [PDF]
Microsyst NanoengKim J, Kim K, Baeck S, Park JY.
europepmc +1 more source
Direct Molding of Luer Connections in PDMS Microfluidic Devices: Comparison with Conventional Interface Methods. [PDF]
Micromachines (Basel)Layedra G +8 more
europepmc +1 more source
Analysing volatile organic compounds (VOCs) with SERS by bubbling into colloidal nanoparticles.
AnalystColleran A +3 more
europepmc +1 more source
Some of the next articles are maybe not open access.
Related searches:
Related searches:
Journal of Medical Engineering & Technology, 1986
The equipment described allows the accuracy of a syringe pump to be tested quickly and conveniently. A digital micrometer assembly clips in place of the disposable syringe and transmits readings to a separate unit which displays flow rates in ml/h. Initial readings of pump output are given in 30 s, with readings to a higher accuracy within 4 min.
M, Nieman, A L, Evans, A, Shaw
openaire +2 more sources
The equipment described allows the accuracy of a syringe pump to be tested quickly and conveniently. A digital micrometer assembly clips in place of the disposable syringe and transmits readings to a separate unit which displays flow rates in ml/h. Initial readings of pump output are given in 30 s, with readings to a higher accuracy within 4 min.
M, Nieman, A L, Evans, A, Shaw
openaire +2 more sources
Engineering in Medicine, 1986
With the evolution of special care baby, intensive care, and coronary care units over the last decade, there has developed a need for greater accuracy in the control of increasingly potent infusions. The design of bedside syringe pump infusers that administer the contents of a syringe to a patient at a constant and predetermined rate will be ...
openaire +2 more sources
With the evolution of special care baby, intensive care, and coronary care units over the last decade, there has developed a need for greater accuracy in the control of increasingly potent infusions. The design of bedside syringe pump infusers that administer the contents of a syringe to a patient at a constant and predetermined rate will be ...
openaire +2 more sources
2018
This is a detailed description of how to make and assembly our open sourse syringe pump.
Mogens Hinge, Bjørn Sjøgren Kilsgaard
openaire +1 more source
This is a detailed description of how to make and assembly our open sourse syringe pump.
Mogens Hinge, Bjørn Sjøgren Kilsgaard
openaire +1 more source
Warming of infusion syringes caused by electronic syringe pumps
Acta Anaesthesiologica Scandinavica, 2003Purpose: To evaluate inadvertent warming of the infusion syringe in four different types of electronic syringe pumps.Methods: Ambient temperature and syringe surface temperature were simultaneously measured by two electronic temperature probes in four different models of commercially available syringe pumps.
Cornelius A +4 more
openaire +3 more sources
SORPTION TO PLASTIC SYRINGES OF DRUGS ADMINISTERED BY SYRINGE PUMP
Journal of Clinical Pharmacy and Therapeutics, 1981SUMMARY The possible sorption of aminophylline, dopamine, heparin, hydrocortisone and insulin to four different makes of plastic syringe was examined. At the concentration of drug normally administered using a syringe pump, no sorption could be detected.
A, Simmons, M C, Allwood
openaire +2 more sources
Intravenous pumps and syringe drivers
2005Abstract Many infusions are given by gravity-assisted drip sets, which give a flow rate dependent on the height of the reservoir above the patient, the length of the tubing, the bore of the intravenous cannula, the density and viscosity of the fluid being delivered, and the patient’s venous pressure.
Patrick Magee, Mark Tooley
openaire +1 more source