Results 191 to 200 of about 151,638 (261)

Rheumatoid Arthritis and Coronary Artery Calcium Progression: A Case Cohort Analysis From ELSA‐Brasil

Arthritis Care &Research, EarlyView.
Objective To investigate the association between rheumatoid arthritis (RA) and coronary artery calcium (CAC) prevalence, incidence, and progression over four years in adults without prior cardiovascular disease. Methods A case‐cohort study within the Brazilian Longitudinal Study of Adult Health (ELSA‐Brasil) included 585 participants (86 patients with ...
Patrícia Fonseca Estrada, Marcos Rafael N. Cavalcante, Itamar de Souza Santos, Márcio S. Bittencourt, Vandrize Meneghini, Paulo A. Lotufo, Alessandra C. Goulart, Isabela M. Bensenor   +7 more
wiley   +1 more source

Love Wave Propagation in a Piezoelectric Composite Structure with an Inhomogeneous Internal Layer. [PDF]

Materials (Basel)
Zhao Y, Li P, Fan G, Shao C.
europepmc   +1 more source

Adaptive Observer for Coupled Wave PDE and Infinite ODE With Sampled Data and Unknown Input: Application to Brain Hemodynamics Estimation

International Journal of Adaptive Control and Signal Processing, EarlyView.
This article proposes a convergent adaptive observer for a damped wave PDE and an infinite‐dimensional ODE coupled in cascade using sampled‐in‐space ODE state measurements. The proposed observer estimates the distributed states of the PDE and ODE along with unknown PDE parameters and spatial input.
Zehor Belkhatir, Sarah Mechhoud, Taous‐Meriem Laleg‐Kirati   +2 more
wiley   +1 more source

Perceive-Assess-Dose-Safeguard: a safety-gated state-action grammar for psychotherapy micro-decisions in computational psychiatry. [PDF]

Front Psychiatry
Niederlohmann E.
europepmc   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Defining synergy for three-phase polymer nanocomposites: a volume-weighted quantitative framework. [PDF]

Sci Rep
Araby S, Bakhbergen U, Han S, Zaied R.
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Finite-Capacity Thermodynamics of Causal Horizons. [PDF]

Entropy (Basel)
Antiba CA.
europepmc   +1 more source

Carboxylic‐Acid Functionalized Multiwalled Carbon Nanotube‐Alkane‐Based Resistive Temperature Sensor for Cold Chain Applications

Advanced Engineering Materials, EarlyView.
This study presents a reversible temperature sensor with high switching ratio, ∼103. The device is fabricated using PET‐ITO and carbon nanotube dispersions in alkane. Considering its application in cold chain logistics, a proof‐of‐concept with LED is showcased. Thus, a temperature drop below the threshold temperature (crystallization temperature of the
Sunil Kumar Behera, Philippe Marrec, A. Jorge Parola, Madalena Dionísio, Hugo Águas, Andreia F. M. Santos, Hamed Pourkheirollah, Donald Lupo, César A. T. Laia   +8 more
wiley   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source