Results 111 to 120 of about 72,530 (285)
Polymer Engineering &Science, Volume 66, Issue 1, Page 364-377, January 2026.Schematic illustration of PA6/SWCNT/CB nanocomposite development and 3D printing for conductive applications. ABSTRACT Conductive polymer nanocomposites for additive manufacturing face a persistent trade‐off, as achieving electrical conductivity requires filler loadings that impair processability and mechanical integrity.
Müslüm Kaplan
wiley +1 more source
Packaging Technology and Science, Volume 39, Issue 1, Page 33-48, January 2026.The study demonstrated that regenerated cellulose films exhibit limited sealability at elevated temperatures due to thermal degradation. Serrated sealing tools enabled tighter seals especially in triple point area, while flat tools resulted in microchannel leaks.
Mahdi Merabtene +3 more
wiley +1 more source
Platinum-group element mineralisation in the Unst ophiolite, Shetland [PDF]
, 1984 The ophiolitic basic and ultrabasic rocks of the island of Unst, Shetland comprise a sequence of harzburgites, dunites, clinopyroxene-rich cumulates, and gabbro, within tectonic blocks that have been thrust over a migmatite complex during the Laxer ...
Gunn, A.G., Leake, R.C., Styles, M.T.
core
GCB Bioenergy, Volume 18, Issue 1, January 2026.Miscanthus is a promising lignocellulosic biomass for diverse material applications. Biobased products are generally expected to offer greenhouse gas advantages over fossil alternatives, yet assessments vary due to methodological choices. This study systematically reviewed 20 peer‐reviewed studies covering 188 comparisons of miscanthus‐derived and ...
Jan Lask +4 more
wiley +1 more source
Resources Chemicals and MaterialsPoly(isoprene-co-glycidyl methacrylate) epoxy macromolecules were synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization to act as interfacial mediators between talcum powder (Talc) and styrene-butadiene rubber (SBR) with ...
Qilai Wang +4 more
doaj +1 more source
Hemoptysis following Talc Pleurodesis in a Pneumothorax Patient
Case Reports in Pulmonology, 2017 The purpose of this article is to report a case of hemoptysis occurring in combination with secondary spontaneous pneumothorax following chemical pleurodesis by talc.
Yusuke Kakiuchi +3 more
doaj +1 more source
Electrical, Microstructural and Physical Characteristics of Talc-based Cordierite Ceramics
, 2022 Ahmed Yahya +5 more
openalex +1 more source
Journal of the American Ceramic Society, Volume 109, Issue 1, January 2026.Abstract This study investigated how SiC PSD influences solid–solid interface to enhance thermal–mechanical properties of ceramic composites. Initial SiCmp particles were milled for 3 h at 200 rpm (microns) and 600 rpm (submicrons) to tune the PSD, and their impact was evaluated in cordierite–mullite matrix, sintered at 1360°C.
John. W. Makokha +9 more
wiley +1 more source
Design of an air-flow microchamber for microparticles detec [PDF]
, 2014 This paper was presented at the 4th Micro and Nano Flows Conference (MNF2014), which was held at University College, London, UK. The conference was organised by Brunel University and supported by the Italian Union of Thermofluiddynamics, IPEM, the ...
4th Micro and Nano Flows Conference (MNF2014) +8 more
core
Mineralogy Controls on Injection‐Induced Fault Slip
Geophysical Research Letters, Volume 52, Issue 24, 28 December 2025.Abstract Fault rocks vary in mineralogy but understanding the role of mineralogy in injection‐induced fault slip behavior remains challenging. We conduct laboratory fluid injection experiments on representative faults with distinct surface mineralogy, injecting fluid at a constant rate of 0.6 mL/min and under a confining pressure of 20 MPa, to examine ...
Fanlin Ling +3 more
wiley +1 more source