Results 251 to 260 of about 2,533,411 (358)

MODELING OPTIMIZATION TASKS IN IT PROJECT MANAGEMENT

Iryna Ivchenko, I. L. Mykheliev, Tetyana Farionova, Natalia R. Knyrik, O. I. Marshak   +4 more
openalex   +2 more sources

Mechanical Behavior and Microstructural Changes Associated with Tensile Deformation above the Martensite Start Temperature during Quenching and Subsequent Partitioning of a Low‐Alloy 37SiB6 Steel

Advanced Engineering Materials, EarlyView.
A new experimental setup, incorporating digital image correlation and infrared thermography in combination with inductive‐conductive heating for precise temperature control, is used to analyze the mechanical behavior and microstructural changes of sheet metal under complex thermomechanical test conditions that represent quench and partitioning ...
Christian Illgen, Benjamin Bohne, Sven Winter, Marcus Böhme, Martin F.-X. Wagner   +4 more
wiley   +1 more source

Critical Human and Organizational Factors for Structural Safety in the Dutch Construction Industry. [PDF]

Am J Ind Med
Ren X, Terwel KC, Yang M, van Gelder PHAJM.   +3 more
europepmc   +1 more source

Combining Metal Additive Manufacturing and Casting Technology: High Performance Cooling Channels for Electric Powertrain Components

Advanced Engineering Materials, EarlyView.
When realized as inserts in high‐pressure die casting, aluminum cooling channels for electric powertrain components and similar applications typically require a stabilizing filler to survive the process. The present study investigates relinquishing this filler using additively manufactured inserts promising performance improvements.
Dirk Lehmhus, Gefei Li, Martin Czekalla, Leonardo Fernandes Gomes, Christoph Pille, Hermann Pleteit, Adrian Struss, Keno Toussaint, Andre Irretier, Münip Dalgic   +9 more
wiley   +1 more source

The effectiveness of dual-task exercises in individuals with chronic obstructive pulmonary disease: a study protocol for a randomized controlled trial. [PDF]

Trials
Ünlü B, Yıldız Özer A, Özmen İ, Polat MG.   +3 more
europepmc   +1 more source

Performance Comparison of Surface Sensitizers for Diode Laser Powder Bed Fusion of Polyamide 12

Advanced Engineering Materials, EarlyView.
Laser‐generated nanoparticles transform standard PA12 powders into high‐performance, dye‐free feedstocks for diode laser 3D printing. Despite identical absorbance at 808 nm, CuS, LaB6, and CB coatings reveal striking differences in fusion and strength—unlocking new design space for recyclable, industrial‐grade polymers.
Michael Willeke, Alexander Sommereyns, Simon Leupold, Arne Lüddecke, Arno Kwade, Nick Hantke, Jan T. Sehrt, Michael Schmidt, Anna R. Ziefuss, Stephan Barcikowski   +9 more
wiley   +1 more source

Reflecting Digital Transformations in Public Health Curricula. [PDF]

Public Health Rev
Hrzic R, Buttigieg S, Wong BLH, Silva AM, Conyard KF, Codd M, Kostkova P, Schutte NM, van Kessel R.   +8 more
europepmc   +1 more source

Microstructural and Mechanical Properties of a Hard Anodic Coating Applied on an Elastically Prestrained Aluminum Substrate

Advanced Engineering Materials, EarlyView.
Prestraining the substrate influences coating formation process. Higher prestraining force leads to higher coating thickness and lower hardness. Increase in prestraining force enhances preliminary damage in hard anodic coating. Fatigue damage mechanisms change for hard anodized prestrained samples.
Linto George Thomas, Lisa Winter, Frank Simchen, Tobias Breitfeld, Thomas Lampke   +4 more
wiley   +1 more source

Translating in-person care to telehealth: a secondary analysis of GP consultations on musculoskeletal conditions. [PDF]

BJGP Open
Li Y, Chan S, Lu L, Jackson TM, Rahimi-Ardabili H, Lau AY.   +5 more
europepmc   +1 more source

A Simulative Evaluation of Triply Periodic Minimal Surface Structures in the Context of Elastocaloric Applications

Advanced Engineering Materials, EarlyView.
A simulative evaluation of triply periodic minimal surface (TPMS) structures for an elastocaloric application under compressive load is performed. For the evaluation of the structure's performance, surface/volume ratio, generated heat and invested mechanical work are taken into account and are compared to a tube as a reference specimen.
Michael Fries, Paul Motzki, Dirk Bähre, Anne Jung   +3 more
wiley   +1 more source