Results 121 to 130 of about 1,228,905 (285)

Interpreting Technical Drawings [PDF]

The Computer Journal, 1990
openaire   +1 more source

Nanoindentation Criteria for Combinatorial Thin Film Libraries

Advanced Engineering Materials, EarlyView.
Thin‐film material libraries are compositional spreads used for screening composition‐structure‐property relationships. Nanoindentation is often used to characterize mechanical behavior across these systems, however variations in methodology are widespread.
Andre Bohn, Adie Alwen, Andrea M. Hodge
wiley   +1 more source

Electrical Conductivities of Conductors, Semiconductors, and Their Mixtures at Elevated Temperatures

Advanced Engineering Materials, EarlyView.
This article presents a comprehensive review of temperature‐dependent electrical conductivity data for multiple material classes at elevated temperatures, highlighting a persistent conductivity gap between metals and semiconductors in the range of 102$\left(10\right)^{2}$– 107$\left(10\right)^{7}$ S/m. Metal–ceramic irregular metamaterials are proposed
Valentina Torres Nieto, Marcia A. Cooper
wiley   +1 more source

On the Influence of Antioxidants and Recycled MgO–C Source Material on the Mechanical Properties of Carbon‐Bonded Magnesia Refractories

Advanced Engineering Materials, EarlyView.
The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann, Tom Weber, Jana Hubálková, Florian Kerber, Dinesh Kumar Gunasekar, Hans Jelitto, Christos G. Aneziris   +6 more
wiley   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Entrepreneurial intentions: The influence of organizational and individual factors [PDF]

An individual's intent to pursue an entrepreneurial career can result from the work environment and from personal factors. Drawing on the entrepreneurial intentions and the person–environment (P–E) fit literatures, and applying a multilevel perspective ...
Foo, Maw Der, Lee, Lena, Leung, Aegean, Wong, Poh Kam   +3 more
core   +1 more source

Low‐Angle Grain Boundaries and Re‐Segregation in Single‐Crystalline Ni‐Base Superalloys

Advanced Engineering Materials, EarlyView.
This work demonstrates that Re‐segregation at low‐angle grain boundaries (LAGBs) in Ni‐base superalloys is influenced by misorientation angle. Advanced microscopy and atom probe tomography reveal that higher misorientation angles increases Re‐segregation.
Alireza B. Parsa, Aparna Saksena, Alesander Kostka, Pascal Thome, Felicitas Scholz, Alexandre Mussi, Christoph Somsen, Baptiste Gault, Jan Frenzel, Gunther Eggeler   +9 more
wiley   +1 more source

PROFESSIONAL TRAINING OF THE FUTURE TECHNOLOGY AND TECHNICAL DRAWING TEACHERS BASED ON THE COMPETENCY APPROACH

Наукові записки Тернопільського національного педагогічного університету імені Володимира Гнатюка. Серія: Педагогіка, 2016
The article outlines the peculiarities of professional training of the future technology and technical drawing teachers. The content characteristics of the concept «professional training of the future technology and technical drawing teacher» are given ...
Lyudmyla Bozhko
doaj  

Numerical Modeling of Tank Cars Carrying Hazardous Materials With and Without Composite Metal Foam

Advanced Engineering Materials, EarlyView.
Large‐scale puncture models consisting of hazardous materials (HAZMATs) tank car with protective steel–steel composite metal foam (S–S CMF) are solved numerically. Tank car plate with added 10.91–13.33 mm thick S–S CMF layer does not puncture. Protective S–S CMF absorbs impact energy, reduces plate deformation, and prevents shear bands formation ...
Aman Kaushik, Afsaneh Rabiei
wiley   +1 more source