Results 181 to 190 of about 10,528,536 (309)

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source

Unipolar memristive switching in bulk negative temperature coefficient thermosensitive ceramics. [PDF]

PLoS One, 2013
Wu H, Cai K, Zhou J, Li B, Li L.
europepmc   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

The temperature coefficient of the velocity of a nervous impulse [PDF]

The Journal of Physiology, 1921
openaire   +2 more sources

Machine Learning‐Supported Analysis for Predicting and Visualizing Nonlinear Relationships Between Material Properties in Electroplated Chromium Layers

Advanced Engineering Materials, EarlyView.
This study applies machine learning regression to predict chromium layer thickness in decorative trivalent chromium electroplating, using 441 experiments from laboratory‐scale (1L) and pilot‐scale (14L) setups. Tree‐based models, particularly CatBoost, outperformed linear regression by capturing nonlinear parameter interactions (R2$R^2$ up to 0.77 ...
Christoph Baumer, Christopher Mai, Luca Eisentraut, Andreas Bund, Ricardo Buettner   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

THE TEMPERATURE COEFFICIENTS OF SOME PHOTOCHEMICAL REACTIONS [PDF]

Proceedings of the National Academy of Sciences, 1929
openaire   +2 more sources

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source