Results 21 to 30 of about 1,569,854 (267)
Brush Seal Temperature Distribution Analysis
Journal of Engineering for Gas Turbines and Power, 2005 Brush seals are designed to survive transient rotor rubs. Inherent brush seal flexibility reduces frictional heat generation. However, high surface speeds combined with thin rotor sections may result in local hot spots. Considering large surface area and accelerated oxidation rates, frictional heat at bristle tips is another major concern especially in
Doğu, Yahya, Akşit, Mahmut Faruk
openaire +3 more sources
Thermotropic Liquid Crystals for Temperature Mapping
Frontiers in Bioengineering and Biotechnology, 2022 Wound management in Space is an important factor to be considered in future Human Space Exploration. It demands the development of reliable wound monitoring systems that will facilitate the assessment and proper care of wounds in isolated environments ...
Vanja Miskovic +6 more
doaj +1 more source
Surface Temperature Distribution of Chinese Kangs [PDF]
International Journal of Green Energy, 2010 This study is attempted to improve local thermal comfort of Chinese kang through improving the uniformity of the faceplate temperature distribution using computational fluid dynamics simulations. The faceplate temperature of kangs is determined by the heat input to the kangs, the smoke flows, and the kang body materials.
Li, Y, Qian, H, Liu, J, Zhang, X
openaire +2 more sources
Temperature non-uniformity in distributed temperature sensors
Electronics Letters, 1993 A study is presented of the effects of temperature non-uniformity in a distributed temperature sensor based on the temperature dependence of Brillouin gain in an optical fibre. The form of the Brillouin gain profile for a given temperature distribution is measured and successfully modelled.
X. Bao, D.J. Webb, D.A. Jackson
openaire +1 more source
Thermal Field Simulation and Optimization of PbF2 Single Crystal Growth by the Bridgman Method
CrystalsPbF2 single crystals are usually grown in the temperature gradient region by the Bridgman–Stockbarger method. Temperature distribution during the growth process is particularly important for the preparation of high-quality crystals.
Lin Li +3 more
doaj +1 more source
Distributing the Frontend for Temperature Reduction [PDF]
11th International Symposium on High-Performance Computer Architecture, 2005 Due to increasing power densities, both on-chip average and peak temperatures are fast becoming a serious bottleneck in processor design. This is due to the cost of removing the heat generated, and the performance impact of dealing with thermal emergencies. So far microarchitectural techniques to control temperature have mainly focused on the processor
Chaparro, Pedro +3 more
openaire +2 more sources
Temperature Distribution in Magnetized Neutron Star Crusts [PDF]
Astronomy & Astrophysics, 2004 We investigate the influence of different magnetic field configurations on the temperature distribution in neutron star crusts. We consider axisymmetric dipolar fields which are either restricted to the stellar crust, ``crustal fields'', or allowed to penetrate the core, ``core fields''. By integrating the two-dimensional heat transport equation in the
Geppert, U., Küker, M., Page, D.
openaire +4 more sources
DEVELOPMENT OF A NEW GENERATION OF TORNUM REX MINING GRAIN DRYERS AND THEIR DESIGN METHODS
Zernovì Produkti ì KombìkormaThe materials of the article analyze the problems and methods of drying grain in modern grain dryers. In recent years, the mixed-flow dryer has been the subject of many studies on drying efficiency, dryer control and productivity improvement.
V. Fitsyk
doaj +1 more source
Metalurgija, 2022 Copper-based materials for electrical purposes usually find their origin in continuous casting lines where the effectiveness of the process and the quality of the final product depends among others on the crystallization system.
P. Strzepek +3 more
doaj
Effect of Evaporator Outflow Rate on Air Distribution in the Computer Laboratory using CFD
International Journal of Electrical, Energy and Power System Engineering, 2020 The ideal room temperature will create comfort in the learning and teaching process. With increasing outdoor air temperature due to climate change, an air conditioner is needed to reach the ideal room temperature. An air conditioner is an air conditioner
Rosyida Permatasari +1 more
doaj +1 more source