Results 101 to 110 of about 3,253,172 (357)
Mechanical Properties of Coronary Veins [PDF]
, 2008 There are several publications available and experiments were done regarding to the vessel biomechanical properties. In the range we could find in vitro and in vivo assessments data for elasticity properties.
Balázs, T. +3 more
core
Advanced Engineering Materials, EarlyView.Equal channel angular pressing of commercial pure copper under low strain amplitude (≈0.48) induces concurrent continuous and localized discontinuous dynamic recrystallization, forming a duplex structure influenced by strain heterogeneity and recovery. Moderate hardening after 4–12 passes results from progressive high‐angle grain boundary formation via
Paula Cibely Alves Flausino +6 more
wiley +1 more source
The stress corrosion resistance and the cryogenic temperature mechanical properties of hot rolled Nitronic 32 bar material [PDF]
The ambient and cryogenic temperature mechanical properties and the ambient temperature stress corrosion properties of hot rolled and centerless ground Nitronic 32 stainless steel bar material are presented.
Montano, J. W. L.
core +1 more source
Advanced Engineering Materials, EarlyView.This study compares the mechanical properties of Inconel 718 with two newly developed compositionally complex alloys (CCAs). Inco‐like‐H alloy demonstrates significantly improved wear resistance, surface finish, and hardness, notably at high temperatures. This CCA requires no heat treatment and is well suited for additive manufacturing. Its performance
Laurent Peltier +3 more
wiley +1 more source
Roll diffusion bonding of titanium alloy panels [PDF]
, 1968 Roll diffusion bonding technique is used for fabricating T-stiffened panel assemblies from titanium alloy. The single unit fabrication exhibits excellent strength characteristics under tensile and compressive loads.
Bennett, J. +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents a comprehensive analysis of the intrinsic relationships and applicability of Hill48 yield criterion. The applicability and error evaluation conditions for Hill48 are established based on specific experimental data. A parameter calibration strategy for N‐value based on error minimization is proposed, and the predictive accuracy is ...
Jinxin Wang +9 more
wiley +1 more source
Development of sputtered techniques for thrust chambers [PDF]
Procedures for closing out coolant passages in regeneratively cooled thrust chambers by triode sputtering, using post and hollow Cu-0.15 percent Zr cathodes are described. The effects of aluminum composite filler materials, substrate preparation, sputter
Allard, P. A. +3 more
core +4 more sources
Advanced Engineering Materials, EarlyView.Laser remelting of a CrMnFeCoNi high‐entropy alloy reveals that optimal chemical homogenization occurs between 30 and 40 J·mm−2. Within this range, elemental segregation is reduced by over 30% compared to the as‐cast state. The study establishes this window as a fast, effective alternative to prolonged annealing for achieving uniform elemental ...
Ajay Talbot +5 more
wiley +1 more source
T55-L-712 turbine engine compressor housing refurbishment-plasma spray project [PDF]
A study was conducted to assess the feasibility of reclaiming T55-L-712 turbine engine compressor housings with an 88 wt percent aluminum to 12 wt percent silicon alloy applied by a plasma spray process.
Leissler, George W., Yuhas, John S.
core +1 more source
Microcellular Poly (Ethylene‐Co‐Vinyl Acetate)/Lignin Nanocomposites for Soft Ferroelectrets
Advanced Engineering Materials, EarlyView.Lignin valorization for advanced porous polymer nanocomposites development and an upscaling route for continuous manufacturing of soft ferroelectrets for energy harvesting are studied. This work examines the role of lignin and carbon nanotubes (CNT) in modifying the mechanical, dielectric, and ferroelectret properties of poly (ethylene‐co‐vinyl acetate)
Yuchen Lian +5 more
wiley +1 more source