Results 121 to 130 of about 290,944 (314)
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source
Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions
Advanced Engineering Materials, EarlyView.This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim +3 more
wiley +1 more source
Yield and tensile strength of vinyl ester composites cured by microwaves
, 2007 In the previous investigation, it was found that the difference in Young’s modulus, ultimate tensile strength and yield strength between microwave cured vinyl ester particulate composites and those cured under ambient conditions is minimal provided low ...
Trada, M. +3 more
core +1 more source
Biotite effect on the anisotropic properties of gneiss in Eastern Himalayas, China
Journal of Rock Mechanics and Geotechnical EngineeringIntact rocks with layered microstructures, such as gneiss, exhibit strong anisotropy. Although anisotropy in the macroscopic strength of gneiss has been widely reported, the role of microstructures in tensile mechanics remains largely unclear.
Shijie Liu +4 more
doaj +1 more source
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading
Advanced Engineering Materials, EarlyView.This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Spinning Apparatus for Measuring Tensile Strength
, 1950 This apparatus was designed by Lyman J. Briggs of the National Bureau of Standards to measure the limiting negative pressure, or tensile strength, of liquids.
Briggs, Lyman J. (Lyman James), 1874-1963
core
Tensile Strength of Uniaxial Composites
Science and Engineering of Composite Materials, 1988 Bader, M.G.
doaj +1 more source