Results 11 to 20 of about 115,498 (264)
Evaluation of Plasticity Models Using Uniaxial Tensile Test
European Mechanical Science, 2020 In this study, it is aimed to evaluate plasticity model prediction performance for plastic behavior of materials using a uniaxial tensile test. For this purpose, von Mises, Hill-48, Hill-93, Barlat-89 and Hu -2003 plasticity models are studied, and DC04,
Emre Esener +2 more
doaj +1 more source
Case Studies in Construction Materials, 2023 The study investigates the variation of tensile strength of high-performance concrete (HPC) based on various tensile tests, such as the flexural test, splitting tensile test, double punch test, and direct tension test, conducted on dog bone specimens ...
Anh-Thang Le, An Le Hoang
doaj +1 more source
Evaluation of measurement uncertainty in a static tensile test
Open Engineering, 2021 This article presents a scheme of the procedure for assessing the measurement uncertainty of material constants determined in the static tensile test.
Graba Marcin
doaj +1 more source
On the estimation of tensile yield stress for polymer materials based on punch tests
Polymer Testing, 2021 The Small Punch Test (SPT) has been widely used for the high throughput evaluation of mechanical properties of metallic materials. However, all the correlations between characteristic punch loads and mechanical properties measured from tensile tests thus
Yi Zhang +5 more
doaj +1 more source
Heritage Science, 2023 Preserving cultural artifacts while minimizing the energy consumption and costs associated with environmental control is crucial. This often requires predicting artifacts degradation caused by temperature and humidity.
Kazuki Ishikawa +4 more
doaj +1 more source
Influence of scratch type on tensile strength in in situ tensile test
Advances in Mechanical Engineering, 2017 In this article, the specimen of Q235 (low carbon steel, C ≤ 0.22%, Mn: 0.3%–0.8%, Si ≤ 0.3%, P ≤ 0.045%, S ≤ 0.05%) has been tested in in situ tensile tests. Especially, different types of scratches are prefabricated with 1, 2, and 3 µm in depth.
Ning Li +8 more
doaj +1 more source
Tensile Specimen’s Permanent Die Designing and Its Al-Mg Alloy Specimen’s Tensile Test
MATEC Web of Conferences, 2016 Based on the facts that there are many kinds of metallic tensile specimens with different dimensions, a set of rectangular cross-section and round cross-section tensile specimens are designed according to China national standard GB228-2002 which is ...
Wang Hongfei, Kong Weibing, Hu Xinping
doaj +1 more source
Dynamic tensile test of single PET textile cables
EPJ Web of Conferences, 2012 The tyres conception involves for certain applications, the use of textile cables as reinforcement. During its use, the tyre undergoes temperatures variations and dynamic loading rates. The consideration of these conditions during the numeric simulations
Pasco F. +3 more
doaj +1 more source
Investigating the effects of loading rate and mixing design on concrete's direct tensile strength using the CTLC test [PDF]
Analytical and Numerical Methods in Mining EngineeringTensile strength of concrete is measured using direct tensile tests on rectangular concrete samples with dimensions: 19 cm in length, 16 cm in width, 6 cm in thickness, and a central hole of 9 cm in diameter.
Manouchehr Sanei +3 more
doaj +1 more source
Application of Instrumented Charpy Method in Characterisation of Materials [PDF]
Interdisciplinary Description of Complex Systems, 2015 Testing of absorbed impact energy according to the Charpy method is carried out to determine the behaviour of a material under the impact load. Instrumented Charpy method allows getting the force displacement curve through the entire test, That curve can
Željko Alar +3 more
doaj +1 more source