Results 91 to 100 of about 14,295,073 (379)

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Tensile test

, 2020
tensile test research for both academics and professional ...
openaire   +1 more source

Hastelloy X properties, data, and metallurgical characteristics [PDF]

, 1968
Literature survey and testing program were initiated to obtain pertinent information for Hastelloy X, a nickel-base alloy, through the temperature range of minus 423 degrees to 1800 degrees F.
Glasier, L. F., Jr.
core   +1 more source

Open challenges in tensile testing of additively manufactured polymers: A literature survey and a case study in fused filament fabrication

Polymer testing, 2022
A. Sola, Wei Juene Chong, Dejana Pejak Simunec, Yuncang Li, A. Trinchi, I. Kyratzis, C. Wen   +6 more
semanticscholar   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

Strength Properties of Preceramic Brazed Joints of a Gold-Palladium Alloy with a Microwave-assisted Oven and Gas/Oxygen Torch Technique [PDF]

, 2014
Statement of problem The effect of microwave brazing on the strength properties of dental casting alloys is not yet known. Purpose The purpose of this study was to compare the strength properties of preceramic brazed joints obtained by using a microwave
Dunford, Robert, Kim, Hyeongil, Monaco, Jr., Edward A., Prasad, Soni   +3 more
core   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Pre-fatigue influence on quasi-static tensile properties of Ti-6Al-4V in thin-sheet form [PDF]

, 2010
The response of engineering structures to loads is most often assessed without taking possible damage of the used material(s) into account. However, it has already been proved that a preceding cyclic loading and the alteration of the microstructure it ...
De Baere, Ives, Degrieck, Joris, Galan Lopez, Jesus, Verleysen, Patricia   +3 more
core   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Development of a Small-Capacity Tensile Testing Machine for Educational Demonstration

JRST: Jurnal Riset Sains dan Teknologi
The tensile testing machine is a device used to characterize the mechanical properties of materials. Most tensile testing machines currently available are designed for high-capacity applications, such as testing metals and concrete, making them less ...
Paryana Puspaputra, Hendra Setiawan, Arif Rahman Hakim   +2 more
doaj   +1 more source