Results 101 to 110 of about 14,295,073 (379)

Tensile Strength of Silicon Nanowires Batch-Fabricated into Electrostatic MEMS Testing Device

Applied Sciences, 2018
The tensile strength of a silicon nanowire (SiNW) that had been integrated into a silicon-on-insulator (SOI)-based microelectromechanical system (MEMS) device was measured using electrostatic actuation and sensing.
Toshiyuki Tsuchiya, Tetsuya Hemmi, Jun-ya Suzuki, Yoshikazu Hirai, Osamu Tabata   +4 more
doaj   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

A universal direct tensile testing method for measuring the tensile strength of rocks

International Journal of Mining Science and Technology
There is limited applicability to the current method for testing the direct tensile strength of rocks because it places stringent requirements on the testing equipment.
Yang Wu, Jianfeng Liu, Zhide Wu, Junjie Liu, Yonghui Zhao, Huining Xu, Jinbing Wei, Wen Zhong   +7 more
doaj   +1 more source

Creep and residual mechanical properties of cast superalloys and oxide dispersion strengthened alloys [PDF]

Tensile, stress-rupture, creep, and residual tensile properties after creep testing were determined for two typical cast superalloys and four advanced oxide dispersion strengthened (ODS) alloys.
Whittenberger, J. D.
core   +1 more source

Water saturation induced changer in the indirect (Brazilian) tensile strength and the failure mode of some igneous rock materials [PDF]

, 2020
The present study concentrates on water induced strength reduction and variation of the failure mode in indirect (Brazilian) tension tests of several igneous rock materials under three moisture cases of oven-dry, air-dry and fully saturated states.
Komurlu, Eren, Yasar, Serdar
core  

Material characterization at high strain by adapted tensile tests [PDF]

, 2011
The strength of materials at high strain levels has\ud been determined using the so-called Continuous-Bendingunder-\ud Tension (CBT) test. This is a modified tensile test\ud where the specimen is subjected to repetitive bending at the\ud same time.
Boogaard, A.H. van den, Emmens, W.C.
core   +3 more sources

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

A new technical approach for real-time tensile strength testing of high-temperature granite based on micro-tensile testing technology

International Journal of Mining Science and Technology
The tensile strength of rocks under real-time high-temperatures is essential for enhanced geothermal system development. However, the complex occurrence and deep burial of hot dry rocks limit the quantity and quality of standard samples for mechanical ...
Xianzhong Li, Yinnan Tian, Zhenhua Li, Shuai Heng, Xiaodong Zhang, Bing Liu   +5 more
doaj   +1 more source

The Evaluation of Laser Weldability of the Third-Generation Advanced High Strength Steel

Metals, 2019
To meet the demands of vehicular safety and greenhouse gas emission reduction, the automotive industry is increasingly using advanced high strength steels (AHSS) in the production of the components.
António B. Pereira, Rafael O. Santos, Bruno S. Carvalho, Marilena C. Butuc, Gabriela Vincze, Luciano P. Moreira   +5 more
doaj   +1 more source

Effects of silane coating on the properties of glass fibre and glass fibre reinforced epoxy resin [PDF]

, 2010
Single fibre tensile testing and microbond testing have been used to benchmark the influence of silane coupling agents on the performance of glass fibre for reinforced epoxy resin composites.
Reilly, S.P., Thomason, J.L.
core