Results 11 to 20 of about 13,596 (257)
Evolution of the Texture in Steelcord
Texture, Stress, and Microstructure, 1991 Tyre industry wishes always wires with best mechanical performances. This continuous improvement of the performances needs the knowledge and the understanding of the deformation process of the wire. To reach this goal, it is useful to know the cristallographic texture and its evolution during the drawing process.The depth of penetration of X Ray not ...
T. Montesin, J. J. Heizmann
openaire +2 more sources
Homogenization estimates for texture evolution in halite [PDF]
Tectonophysics, 2005 In this work, the recently developed “second-order” self-consistent method [Liu, Y., Ponte Castaneda, P., 2004a. Second-order estimates for the effective behavior and field fluctuations in viscoplastic polycrystals. J. Mech. Phys. Solids 52 467–495] is used to simulate texture evolution in halite polycrystals.
Liu, Yi +2 more
openaire +5 more sources
Quantitative Analysis of Shear Texture Evolution in Accumulative Roll Bonded AA 1060 Aluminum Alloy
CrystalsAA 1060 aluminum alloy underwent roll bonding with reductions of 25% and 35%, followed by accumulative roll bonding (ARB) for up to seven cycles at ambient temperature.
Peng Du +6 more
doaj +2 more sources
Texture evolution of amaretti cookies during storage [PDF]
, 2006 The results of a study on texture evolution during 35 days of storage of ldquoamarettirdquo, a typical Italian cookie, packaged in two different ways are reported. Amaretti cookies were wrapped in polyvinylchloride (PVC) film or aluminium foil (ALL), to simulate two different permeability conditions and stored at controlled temperature and humidity ...
Piga, Antonio +3 more
core +4 more sources
Modeling texture evolution during rolling of magnesium alloy AZ31
, 2022 S.285-290Due to crystallographic texture rolled magnesium sheets exhibit strongly aniso-tropc and asymmetric plastic behavior. Therefore the simulation of texture evolution during manufacturing is a prerequisite for the prediction of the material ...
Riedel, H., Walde, T.
core +1 more source
Metals, 2017 Microstructure, texture evolution, and mechanical properties of Ti–6Al–1.5Cr–2.5Mo–0.5Fe–0.3Si (VT3-1) titanium alloy processed by multi-pass drawing and subsequent isothermal annealing were systematically investigated.
Xiaofei Lei +6 more
doaj +1 more source
Metals, 2021 In this study, hot rolling trials were conducted on a twin-roll cast and homogenized magnesium alloy Mg-6.8Y-2.5Zn (WZ73). The WZ73 contains long period stacking ordered (LPSO) structures due to the ratio of Y and Zn content.
Madlen Ullmann +2 more
doaj +1 more source
Metals, 2022 In this paper, the VPSC (visco-plastic self-consistent) model was improved by considering the effect of heating rate. The hot compression deformation behavior and texture evolution of AA7075 were studied based on the improved VPSC model and EBSD ...
Siyuan Zhu +3 more
doaj +1 more source
Texture Evolution in Hydroentangled Nonwovens [PDF]
International Nonwovens Journal, 2003 We recently reported on a co-occurrence-based method for texture analysis. This paper uses this texture analysis method to examine the development of the texture during hydroentangling as a function process conditions. We report on the development of texture as a function of hydroentangling energy.
O.B. Berkalp, B. Pourdeyhimi, A. Seyam
openaire +1 more source
Experimental Investigation on Local and Global Texture Evolution in Drawing Seamless Copper Tubes
Applied Mechanics, 2023 Mass flow inequality in the initial stage of tube processing can lead to eccentricity and micro- and nano-structural changes that affect residual stress and texture development.
Somayeh Khani +3 more
doaj +1 more source