Results 61 to 70 of about 578,151 (295)
Texture Modelling with Nested High-order Markov-Gibbs Random Fields
, 2015 Currently, Markov-Gibbs random field (MGRF) image models which include high-order interactions are almost always built by modelling responses of a stack of local linear filters.
Gimel'farb, Georgy +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar +2 more
wiley +1 more source
Signature Verification Approach using Fusion of Hybrid Texture Features
, 2019 In this paper, a writer-dependent signature verification method is proposed. Two different types of texture features, namely Wavelet and Local Quantized Patterns (LQP) features, are employed to extract two kinds of transform and statistical based ...
Alaei, Alireza +2 more
core +1 more source
Mutual influence of cross hatch angle and superficial roughness of honed surfaces on friction in ring-pack tribo-system [PDF]
, 2013 The cylinder bore surface texture, widely produced by the honing technique, is an essential factor for a good engine performance (friction, oil consumption, running-in, wear etc.).
DEMIRCI, Ibrahim +3 more
core +6 more sources
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Quantitative Ultrasound and B-mode Image Texture Features Correlate with Collagen and Myelin Content in Human Ulnar Nerve Fascicles [PDF]
, 2019 We investigate the usefulness of quantitative ultrasound (QUS) and B-mode texture features for characterization of ulnar nerve fascicles. Ultrasound data were acquired from cadaveric specimens using a nominal 30 MHz probe. Next, the nerves were extracted
Andre, Michael +6 more
core +1 more source
Texture analysis of vertebral bone marrow using chemical shift encoding–based water-fat MRI:a feasibility study [PDF]
, 2019 Summary This feasibility study investigated the spatial heterogeneity of the lumbar vertebral bone marrow using chemical shift encoding–based water-fat MRI. Acquired texture features like contrast and dissimilarity allowed for differentiation of pre- and
Baum, T. +12 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
Modeling of evolving textures using granulometries [PDF]
, 2006 This chapter describes a statistical approach to classification of dynamic texture images, called parallel evolution functions (PEFs). Traditional classification methods predict texture class membership using comparisons with a finite set of predefined ...
Gray, Alison +2 more
core