Results 41 to 50 of about 28,078 (291)

Method Validation for Determination of Thallium by Inductively Coupled Plasma Mass Spectrometry and Monitoring of Various Foods in South Korea

Molecules, 2021
Thallium (Tl) is a rare element and one of the most harmful metals. This study validated an analytical method for determining Tl in foods by inductively coupled plasma mass spectrometry (ICP-MS) based on food matrices and calories. For six representative
Yeon-hee Kim, Wook-jin Ra, Solyi Cho, Shinai Choi, Bokyung Soh, Yongsung Joo, Kwang-Won Lee   +6 more
doaj   +1 more source

Exploring patients’ profiles associated with the resolution of acute calcium pyrophosphate arthritis treatedwith colchicine and prednisone: post hoc analysis of a randomized controlled trial

Arthritis Care &Research, Accepted Article.
Objective The objective was to identify factors determining acute arthritis resolution and safety with colchicine and prednisone in acute calcium pyrophosphate (CPP) crystal arthritis. Methods We conducted a post hoc analysis of the COLCHICORT trial, which compared colchicine and prednisone for the treatment of acute CPP crystal arthritis, using a ...
Tristan Pascart, Laurène Norberciak, Pascal Richette, Pierre Robinet, Aurore Pacaud, Gauthier Marchasson, Thibault Rabin, Hélène Luraschi, Pierre Maciejasz, Anne‐France Georgel, Augustin Latourte, Hang‐Korng Ea, Sébastien Ottaviani, Charlotte Jauffret, Vincent Ducoulombier   +14 more
wiley   +1 more source

Thermodynamic properties of the liquid Hg-Tl alloys determined from vapour pressure measurements [PDF]

Journal of Mining and Metallurgy. Section B: Metallurgy, 2002
The partial vapour pressure of mercury over liquid Hg-Tl liquid solutions were determined in the temperature range from 450 to 700 K by direct vapour pressure measurements carried out with the quartz gauge. From the measured ln pHg vs.
Gierlotka W., Fitzner K., Sukiennik M.
doaj   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

On the Deformation Behavior of Metastable CrMnNi Steels Processed by Directed Energy Deposition in Different Temperature Regimes

Advanced Engineering Materials, EarlyView.
In the present study, metastable CrMnNi steels with varying chemical compositions and a concomitantly altered stacking fault energy are processed via directed energy deposition and afterwards tested via tensile tests at different temperatures. The present study shows the influence of the manufacturing process on the elemental deformation mechanisms for
Julia Richter, Thomas Wegener, Florian Stredak, Gert Bartzsch, Steffen Scherbring, Javad Mola, Olena Volkova, Stefan Böhm, Thomas Niendorf   +8 more
wiley   +1 more source

Microstructural Evolution and Mechanical Properties of a Medium‐Manganese Steel Manufactured by Laser‐Based Powder Bed Fusion of Metals

Advanced Engineering Materials, EarlyView.
Fe–12Mn–0.2C medium‐manganese steel is processed by laser‐based powder bed fusion of metals using blended as well as pre‐alloyed powder. Various scanning speeds are used to determine the influence of energy deposition rate on microstructure and mechanical properties.
Leoni Hübner, Bugra Köksal, Thomas Wegener, Christian Haase, Thomas Niendorf   +4 more
wiley   +1 more source

Spectrophotometric Determination of the Trace Amount of Thallium in Water and Urine Samples by Novel Oxidative Coupling Reaction

E-Journal of Chemistry, 2009
A novel, simple, rapid, sensitive and selective method has been proposed for the trace determination of thallium by spectrophotometric detection. This method is based on the oxidation of MBTH (3-methyl-2-benzothiazolinone hydrazone hydrochloride) by ...
P. Nagaraja, N. Ghllab Saeed Al-Tayar, A. Shivakumar, A. K. Shresta, A. K. Gowda   +4 more
doaj   +1 more source

Micromechanical Insights into Sinter‐Based Additively Manufactured NiTi with Nb as a Sintering Aid

Advanced Engineering Materials, EarlyView.
This study investigates the microstructural and micromechanical behavior of NiTiNb made through filament‐based materials extrusion via chemically correlated nanoindentation. B19' remnants from the original powder lead to Nb gradients within NiTiNb grains due to the short sintering times required in liquid‐phase sintering.
Nerea Abando, Rebecca A. Gallivan, Nensi Toncich, Arnold Müller, Ralph Spolenak   +4 more
wiley   +1 more source

Effect of Annealing Temperature on Microstructure and Dry‐Sliding Behavior of Powder Bed Fusion–Laser Beam Ti6Al2Sn4Zr6Mo Alloy

Advanced Engineering Materials, EarlyView.
Heat treatment parameters critically affect the wear resistance of powder bed fusion–laser beam (PBF‐LB)‐produced Ti–6Al–2Sn–4Zr–6Mo alloy. This study found that optimizing annealing temperature allows to obtain a tailored microstructure, which enhances the dry‐sliding behavior by forming a stable and functional mechanically mixed layer (MML), ensuring
Gianluca Pirro, Lavinia Tonelli, Carla Martini, Alessandra Martucci, Mariangela Lombardi, Lorella Ceschini   +5 more
wiley   +1 more source

Study of Formation and Phase Composition of Thallium Selenide Layers on Polycaproamide

Medžiagotyra, 2015
Thepolycaproamide PA 6 films were modified with layers of thallium selenide, TlxSey. A two stage process was used to deposit these thinlayers involves: seleniumization in 0.05 mol·dm–3 K2SeS2O6solution of 0.1 mol·dm–3 HCl and 60 oCfollowed by treatment ...
Remigijus Ivanauskas, Linas Samardokas, Ingrida Ancutienė, Algimantas Ivanauskas   +3 more
doaj   +1 more source