Results 91 to 100 of about 127,616,970 (139)

An Investigation of Efficiency Issues in a Low-Pressure Steam Turbine Using Neural Modelling. [PDF]

Sensors (Basel)
Bělohoubek M, Liška K, Kubín Z, Polcar P, Smolík L, Polach P.   +5 more
europepmc   +1 more source

Stresses and Strains of Equipment Inside a WWER-1000 Nuclear Reactor

Biuletyn Instytutu Spawalnictwa, 2016
O.W. Machnienko, I.W. Mirzov
openaire   +2 more sources

Evaluation of the Embrittlement in Reactor Pressure-Vessel Steels Using a Hybrid Nondestructive Electromagnetic Testing and Evaluation Approach. [PDF]

Materials (Basel)
Vértesy G, Rabung M, Gasparics A, Uytdenhouwen I, Griffin J, Algernon D, Grönroos S, Rinta-Aho J.   +7 more
europepmc   +1 more source

PRINCIPLES OF WATER SUPPLY REGULATION OF THE WWER-1000 STEAM GENERATOR

Young Scientist, 2020
Mykhailo Yarotskyi, Oleksandr Brunetkin
openaire   +1 more source

Some of the next articles are maybe not open access.

Related searches:

Analysis of embrittlement of WWER-1000 RPV materials

International Journal of Pressure Vessels and Piping, 2012
Abstract Analysis of embrittlement for WWER-1000 RPV materials is performed on the basis of available and original experimental data. Contributions of thermal aging and neutron irradiation to embrittlement are considered for base and weld metals. Equations have been obtained for the shift of the critical temperature of brittleness as a function of ...
B Z Margolin, D Yu Erak
exaly   +2 more sources

Basic results of the Russian WWER-1000 surveillance program

Nuclear Engineering and Design, 1997
The surveillance test results of the reactor pressure vessels (RPV) of three Russian WWER-1000 type units designated Units 1, 2 and 3 are given and the embrittlement rates compared to those predicted by the Russian Regulatory Guide. The surveillance materials properties measured by manufacturers of the RPVs are reviewed.
Kryukov, A., Nikolaev, Yu.A., Planman, Tapio, Platonov, P.   +4 more
core   +5 more sources

Probability of Rupture for WWER-1000 Main Piping

Volume 2: Nuclear Policy; Nuclear Safety, Security, and Cyber Security; Operating Plant Experience; Probabilistic Risk Assessments; SMR and Advanced Reactors, 2020
Abstract A probability of rupture for WWER-1000 main piping was calculated based on the Failure Assessment Diagram (FAD), treating material properties of welds (the most likely zone for crack growing and its nucleation) and crack morphology parameters as stochastic values.
Yaroslav Dubyk, Maksym Zarazovskii, Sergii Ageiev, Vladislav Filonov   +3 more
openaire   +1 more source

Assessment of the WWER-1000 reactor condition

International Journal of Pressure Vessels and Piping, 2006
The current state of the materials (steel, welds, anticorrosive cladding metal) of WWER-1000 RPVs has been examined, taking into consideration special features of their manufacture and operation for 30 years. The possibility of operating these reactors after their design service life has been estimated, allowing for the degradation of properties due to
B.T. Timofeev, G.P. Karzov
openaire   +1 more source

Development of alternative fuel assembly for WWER-1000 reactor

Nuclear Engineering and Design, 1997
Abstract An alternative design of fuel assembly has been developed for the WWER-1000 reactor with the aim of assuring a geometrical stability of the core during operation. The fuel assembly provides enhanced safety and substantial improvement in the WWER-1000 fuel cycle economics.
Mikhail I. Solonin, Yuri K. Bibilashvili, Nikolai B. Sokolov, Albert K. Panyushkin, Vladimir Tsibulia, Oleg B. Samoylov, Vadim B. Kurilev, Vladimir S. Kuul, Vladimir S. Kuul, Viktor B. Kaidalov, Rudolf A. Peskov, Valentin F. Ershov   +11 more
openaire   +1 more source