Results 111 to 120 of about 143,501 (306)
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Case Studies in Thermal EngineeringConsidering the anisotropic heat conduction and temperature-dependent thermal conductivity is of great significance for the ablation behavior of carbon/carbon (C/C) composites.
Kexin Wang +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Radiology and Oncology, 2019 To compare the frequency of adverse events of thermal microwave (MWA) and radiofrequency ablation (RFA) with non-thermal irreversible electroporation (IRE) in percutaneous ablation of hepatocellular carcinoma (HCC).
Verloh Niklas +10 more
doaj +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
Research progress in ablative resistant ethylene■propylene■diene terpolymer
Hecheng xiangjiao gongyeEthylene■propylene■diene terpolymer （EPDM） was a new type of ablation■resistant matrix material with low density, good thermal stability and excellent ablation resistance, and it found extensive applications in aerospace, thermal protection and other ...
ZHAO Dong-wei1, WEN Yan-wei2, FU Quan-sheng1, CHEN Meng-han1, YANG Zi-fan1, JIA Hong-bing1
doaj +1 more source
The current status of thermal ablation in the management of T1b renal masses
International Journal of Hyperthermia, 2019 The role of thermal ablation in the management of T1b renal masses is not well defined. The purpose of this review is to examine current evidence for cryoablation, radiofrequency ablation, and microwave ablation of T1b renal masses as well as review ...
BT Welch +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Interdisciplinary Neurosurgery, 2014 Background: Chordomas are rare malignant tumors that are difficult to treat and have high recurrence rates despite aggressive therapy. Objectives: We present the first case of a patient with a clival chordoma in which complete tumor ablation was achieved
James Barrese +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source