A review of the erosion of thermal barrier coatings [PDF]
Journal of Physics D: Applied Physics, 2007 The application of thermal barrier coatings (TBCs) to components with internal cooling in the hot gas stream of gas turbine engines has facilitated a steep increase in the turbine entry temperature and the associated increase in performance and efficiency of gas turbine engines.
Wellman, R. G., Nicholls, John R.
openaire +4 more sources
Parametric Studies Of Failure Mechanisms In Thermal Barrier Coatings During Thermal Cycling Using FEM [PDF]
International Journal of Applied Mechanics and Engineering, 2015 Thermal barrier coatings (TBCs) are widely used on different hot components of gas turbine engines such as blades and vanes. Although, several mechanisms for the failure of the TBCs have been suggested, it is largely accepted that the durability of these
B. Srivathsa, D.K. Das
doaj +2 more sources
Microstructural characterization of a plasma sprayed ZrO2-Y2O3-TiO2 thermal barrier coating [PDF]
, 1996 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.The use of plasma sprayed ceramic coats as thermal barrier coatings (TBCs) for the protection of metallic structures and equipment from severe thermal ...
Diaz Angülo, Pedro Antonio
core +7 more sources
Computer model to predict electron beam-physical vapour deposition (EB-PVD) and thermal barrier coating (TBC) deposition on substrates with complex geometry [PDF]
, 2000 For many decades gas turbine engineers have investigated methods to improve engine efficiency further. These methods include advances in the composition and processing of materials, intricate cooling techniques, and the use of protective coatings ...
Pereira, Vitor Emanuel M. Loureiro S.
core +6 more sources
Microstructural damage of thermal barrier coatings due to CMAS [PDF]
, 2013 Over recent years, due to a constant desire for higher efficiency engines and hence increased turbine entry temperatures and a proportional reduction in [Carbon dioxide] emissions, there is a need to understand how molten slags (CMAS: Calcia magnesia ...
Ndamka, Ngunjoh Lawrence
core +7 more sources
Erosion of Ceramic Thermal Barrier Coatings [PDF]
CORROSION 1984, 1984 Abstract A study has been made to relate the erosion behavior of several experimental zirconia-base ceramic thermal barrier coatings to their processing parameters and microstructure. The incremental erosion rates were measured and each specimen was examined using optica and scanning electron microscopy.
Davis, A.G., Boone, D.H., Levy, A.V.
openaire +2 more sources
Research Status of Thermal Barrier Coatings in Aero-engine Application
Hangkong gongcheng jinzhan, 2020 With the increase of the operation environment requirements for aero-engine, the thermal barrier coating technology is difficult to satisfy the development requirement of aero-engine in the aspects of thermo-physical properties and thermo-stability.
PENG Rui, CHANG Zhendong, SUN Lili
doaj +1 more source
Progress on Zirconia-based Ceramics for Thermal Barrier Coatings
Hangkong gongcheng jinzhan, 2018 Zirconia-based ceramics for thermal barrier coatings is a key technology of aircraft engine. According to the investigation report of stable zirconia-based ceramics for thermal barrier coatings doped with one component oxide, two component oxides and ...
Zhang Wei
doaj +1 more source
A review of the high-entropy ceramic materials for thermal barrier coatings: Design, synthesis, sintering and properties [PDF]
Processing and Application of CeramicsThermal barrier coatings are used as a surface technology for hot-end components of turbine engines, and the continuous development of aerospace technology puts higher requirements on ceramic materials for thermal barrier coatings. High-entropy ceramics,
Liu Jiahang +7 more
doaj +1 more source
Reinforced sol–gel thermal barrier coatings and their cyclic oxidation life [PDF]
, 2013 Cyclic oxidation life enhancement of sol–gel thermal barrier coatings is obtained via the reinforcement of the controlled micro-crack network that forms during the initial sintering of the deposit.
Ansart, Florence +5 more
core +1 more source