Results 121 to 130 of about 749,354 (336)

Enhanced Oxidation and Thermal Shock Resistance of N‐type Mg2Si0.89(Sn0.1,Sb0.01) Thermoelectric Material via Cr0.9Si0.1 Coating

Advanced Engineering Materials, EarlyView.
Cr0.9Si0.1 protective coatings are developed to enhance the thermal‐shock and oxidation resistance of Mg2Si0.89(Sn0.1,Sb0.01) thermoelectric (TE) materials. The coating forms a dense and adherent barrier that suppresses oxygen diffusion and mitigates mechanical degradation during cyclic oxidation, demonstrating its potential to improve the long‐term ...
Mikdat Gurtaran, Zhenxue Zhang, Xiaoying Li, Hanshan Dong   +3 more
wiley   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Dependence of thermal conductivity on radiation defects in ThO2 investigated by molecular dynamics method

Nuclear Materials and Energy
Nuclear fuel performance would be deteriorated due to radiation defects. Therefore, investigating the effect of irradiation-induced defects on nuclear fuel properties is essential. Thermal conductivity is an important property of nuclear fuel.
Ziqiang Wang, Chen Yang, Miaosen Yu, Wenxue Ma, Liyao Guo, Zhixian Wei, Ning Gao, Zhongwen Yao, Xuelin Wang   +8 more
doaj   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

A Multi-Scale Numerical Simulation on Thermal Conductivity of Bio-Based Construction Materials [PDF]

, 2022
Gang Huang, Ariane Abou‐Chakra, Sandrine Geoffroy, Joseph Absi   +3 more
openalex   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Bimetallic (NiFe) and Trimetallic (NiFeCr) Nanoalloys from Metal Oxides Using a Microwave Hydrogen Plasma

Advanced Engineering Materials, EarlyView.
Bimetallic (NiFe) and trimetallic (NiFeCr) nanoalloys (NAs) are synthesized using corresponding oxide mixtures using microwave hydrogen plasma within a few milliseconds. The process simultaneously 1) reduces metal oxides to metals; 2) downsizes the particles from micrometers to nanometers; and 3) blends the metals to form NAs.
Sachin Kumar, Mohammad Kazemi, Zichang Xiong, Thomas Cameron, Julian Held, Uwe Kortshagen   +5 more
wiley   +1 more source

Inflammatory Response‐Inspired Thermochromic Shield for Pneumatic Structures

Advanced Engineering Materials, EarlyView.
A thermochromic shield for pneumatic structures is developed, using anhydrous sodium acetate powder and thermochromic pigment‐included solution. In this shield composed of three layers, the exothermic and thermochromic reactions, followed by the mixture of both components, occur promptly with an incident of penetrating damage as a sign of initial ...
Hyun Jae Lee, Ryuma Niiyama
wiley   +1 more source