Results 101 to 110 of about 359,627 (267)

Influence of non-uniform magnetic field on the thermal efficiency hydrodynamic characteristics of nanofluid in double pipe heat exchanger. [PDF]

Sci Rep, 2023
Azizi Y, Bahramkhoo M, Kazemi A.
europepmc   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

High Compression Ratio Active Pre-chamber Single-Cylinder Gasoline Engine with 50% Gross Indicated Thermal Efficiency. [PDF]

ACS Omega, 2023
Zhan W, Chen H, Du J, Wang B, Xie F, Xie F, Li Y.   +6 more
europepmc   +1 more source

Thermomechanical Fatigue and Creep–Fatigue Interaction of Inconel 718 Additively Manufactured by Laser Beam Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth, Tomáš Babinský, Jan Lars Riedel, Wen Hao Kan, Aijun Huang, Martin Heilmaier, Ivo Šulák   +6 more
wiley   +1 more source

Performance Analysis and Optimization of a Channeled Photovoltaic Thermal System with Fin Absorbers and Combined Bi-Fluid Cooling

Computation
The conversion efficiency of photovoltaic (PV) cells can be increased by reducing high temperatures with appropriate cooling. Passive cooling systems using air, water, ethylene glycol, and air/water+TiO2 nano bi-fluid froth in the duct channel have been ...
Hamza Nasri, Jamel Riahi, Hatem Oueslati, Hichem Taghouti, Silvano Vergura   +4 more
doaj   +1 more source

Effects of Installing Different Types of Cooling Fins on the Cold Side of a Thermoelectric Power Generation Device on the Thermal Efficiency and Exergy Efficiency of Power Cable Surface Waste Heat Recovery. [PDF]

Micromachines (Basel), 2023
Hu Z, de León F, Wang R, Li Y.
europepmc   +1 more source

Low‐Temperature Imidization of Polyimides (PI) for Scalable Manufacturing of Flexible Wearable Electronics

Advanced Engineering Materials, EarlyView.
Low‐temperature imidization of PEG‐modified polyimide enables fully screen‐printed, roll‐to‐roll fabrication of flexible electrodes on PET substrates, delivering robust mechanical durability and reliable ECG/EMG signal performance for wearable electronics.
Akib Abdullah Khan, Jong‐Hoon Kim
wiley   +1 more source

A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data

Advanced Engineering Materials, EarlyView.
Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour, Prithwish Tarafder, Anton Wiberg, Huanyu Li, Johan Moverare, Patrick Lambrix   +5 more
wiley   +1 more source

The improved thermal efficiency of Prandtl-Eyring hybrid nanofluid via classical Keller box technique. [PDF]

Sci Rep, 2021
Jamshed W, Baleanu D, Nasir NAAM, Shahzad F, Nisar KS, Shoaib M, Ahmad S, Ismail KA.   +7 more
europepmc   +1 more source

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source