Results 171 to 180 of about 508,590 (314)
Thermogravimetric/Thermal-Mass Spectroscopy Insight into Oxidation Propensity of Various Mechanochemically Made Kesterite Cu2ZnSnS4 Nanopowders. [PDF]
Materials (Basel)Lejda K, Partyka J, Janik JF.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Thermal conductivity modeling of nanofluids
, 2011 This paper was presented at the 3rd Micro and Nano Flows Conference (MNF2011), which was held at the Makedonia Palace Hotel, Thessaloniki in Greece.
Croft, NT +2 more
core
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition
Advanced Engineering Materials, EarlyView.AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley +1 more source
Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors
Advanced Engineering Materials, EarlyView.We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay +3 more
wiley +1 more source
Dynamic thermal modelling using CFD
, 2003 This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Buildings expend vast quantities of energy, which has a detrimental impact on the environment.
Somarathne, Shini
core
Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids
Advanced Functional Materials, EarlyView.This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow +9 more
wiley +1 more source