Results 121 to 130 of about 696,535 (296)
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Modeling, Analysis, and Optimization Issues for Large Space Structures [PDF]
Topics concerning the modeling, analysis, and optimization of large space structures are discussed including structure-control interaction, structural and structural dynamics modeling, thermal analysis, testing, and ...
Amos, A. K. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
STRUCTURE DYNAMIC CHARACTER OPTIMIZATION AT THERMAL ENVIRONMENT
Jixie qiangdu, 2015 Many aircraft structures are in thermal and vibration composite environment,and the two both should be taken into account in structural optimization design. Thermal environment influences the structural dynamic characteristics on the change of structural
XUE HongJun, ZHANG Yong, ZHANG XiaoYan
doaj
Advanced Engineering Materials, EarlyView.The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht +5 more
wiley +1 more source
A Knowledge‐Based Approach for Understanding and Managing Additive Manufacturing Data
Advanced Engineering Materials, EarlyView.Additive manufacturing processes generate a large amount of data. Effectively managing, understanding, and retrieving information from this data remains a major challenge. Therefore, we propose an ontology‐based approach to integrate heterogeneous data, enable semantic queries, and support decision‐making.
Mina Abd Nikooie Pour +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang +3 more
wiley +1 more source
Development of a Thermal Management System for Electrified Aircraft [PDF]
This paper describes the development and optimization of a conceptual thermal management system for electrified aircraft. Here, a vertical takeoff and landing (VTOL) vehicle is analyzed with the following electrically sourced heat loads considered ...
Chapman, Jeffryes W. +2 more
core +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source