Results 81 to 90 of about 61,264 (311)

Evaluation of the Photovoltaic System Installation Impact to an Electric Power Grid Part 2: Impact analysis of photovoltaic installation to an electric power grid by applying a nonlinear analysis model

Labor & Engenho, 2016
The impact of the installation of a large-scale photovoltaic (PV) system to the electric power grid management is analyzed in a series of two works: Part 1 and Part 2. The PV generation is estimated in Part 1.
Juan Ernesto Wyss Porras, Susumu Shimada, Jun Yoshino, Tomonao Kobayashi   +3 more
doaj   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Hydro energy potential of cooling water at the thermal power plant

, 2011
The hydro energy of the gravity water flow from the coal-fired thermal power plant units to the river in an open cooling system of turbine condensers is determined.
Stevanović, Vladimir, Maslovarić, Blaženka, Gajić, Aleksandar, Dusan Arnautovic, Ljubodrag Savic, Milivojević, Sanja, Dašić, Tina, Prica, Sanja, Sanja Prica, Bojan Milovanovic, Savić, Ljubodrag, Milovanović, Bojan, Kuzmanović, Vladan, Aleksandar Gajic, Tina Dasic, Arnautović, Dušan, Blazenka Maslovaric, Vladimir D. Stevanovic, Vladan Kuzmanovic   +18 more
core   +1 more source

Modeling of Large-Scale Thermal Power Plants for Performance Prediction in Deep Peak Shaving

, 2022
To integrate more renewable energy into the power grid, large-scale thermal power plants have to extend their operating ranges and participating in deep peak shaving.
Sha Liu, Jiong Shen
core   +1 more source

Thermal Power Plants - Flue Gas Purification

Tehnički Glasnik
One of the most important problems today is the formation of greenhouse gases, mainly caused by the emission of flue gases in thermal power plants: carbon dioxide (CO2), sulfur dioxide (SO2) and nitrogen oxides (NOx) ("acid rain").
Marinko Stojkov, Damir Šljivac, Ante Čikić, Robert Šanta   +3 more
doaj   +1 more source

Thermodynamic Pathways of Nonequilibrium Solidification in Wire‐Arc Additive Manufacturing Fe‐Based Multicomponent Alloy Structures

Advanced Engineering Materials, EarlyView.
Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios, Anthony Gonzalez, Aleksander Aleman, Tyler Dolmetsch, Tanaji Paul, Arvind Agarwal   +5 more
wiley   +1 more source

Estimating the Impact of Restructuring on Electricity Generation Efficiency: The Case of the Indian Thermal Power Sector [PDF]

We examine the impact of electricity sector restructuring on the operating efficiency of coal-fired power plants in India. Between 1995 and 2009, 85 percent of coal-based generation capacity owned by state governments was unbundled from vertically ...
Kabir Malik, Maureen Cropper, Alexander Limonov, Anoop Singh   +3 more
core  

A study of trilateral flash cycles for low-grade waste heat recovery-to-power generation [PDF]

, 2014
There has been renewed significance for innovative energy conversion technologies, particularly the heat recovery-to-power technologies for sustainable power generation from renewable energies and waste heat. This is due to the increasing concern over
Ajimotokan, Habeeb A.
core  

Tailored Hierarchical Porous Copper Architectures via Three Dimensional Printing and Pressure‐less Sintering for Next‐Generation Lithium‐Metal Batteries

Advanced Engineering Materials, EarlyView.
A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley   +1 more source

Flexibility in thermal power plants [PDF]

, 2017
FLEXIBILITY IN THERMAL POWER PLANTS Flexibility in thermal power plants (Rights reserved) (-

core