Results 71 to 80 of about 797,519 (300)
Flexible Electric Power Control for Coal-Fired Units by Incorporating Feedwater Bypass
IEEE Access, 2019 The improvement of the operating flexibility of a thermal power unit has always been an essential issue due to its substantial support to power system stability. In addition, this issue has become increasingly important for the large-scale integration of
Wei Wang +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
EFFICIENCY ESTIMATION OF THERMAL POWER PLANT WITHOUT DIVIDING FUEL CONSUMPTION IN PRODUCT TYPES
Известия высших учебных заведений и энергетических объединенний СНГ: Энергетика, 2005 Combined Thermal Power Plant unit is considered as an exergy generator. Exergy is supplied to consumers by streams of various power carriers. It allows to exclude division of the equipment and fuel consumption in product types and to propose extremely ...
A. E. Piir, V. B. Kuntysh
doaj
Setting requirements to carbon intensity of thermal power plants [PDF]
E3S Web of ConferencesThe article proposes and substantiates benchmarks of specific greenhouse gas emissions as targets to turn to more advanced and environmentally friendly production mode while reducing carbon intensity of the thermal power industry.
Roslyakov Pavel +4 more
doaj +1 more source
Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio
Advanced Engineering Materials, EarlyView.This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov +4 more
wiley +1 more source
Research on Fault Diagnosis of Thermal Power System of Thermal Power Unit under Different Loads
Journal of Physics: Conference SeriesAbstract Aiming at the problem of difficulty in acquiring fault data under different loads, a domain-adversarial-based fault diagnosis method for convolutional neural networks is established by combining convolutional neural networks with adversarial domain adaptive methods.
Liming Deng +5 more
openaire +1 more source
5MW Power Upgrade Studies of the ISIS TS1 Target [PDF]
, 2015 The increasing demand for neutron production at the ISIS neutron spallation source has motivated a study of an upgrade of the production target TS1.
Booth, Christopher N. +5 more
core
Advanced Engineering Materials, EarlyView.This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff +9 more
wiley +1 more source
Increasing the operation efficiency of low pressure cylinders of cogeneration turbines [PDF]
, 2017 Первичные ресурсы в тепловой энергетике преобразуются в два вида энергии: электрическую и тепловую. Если первый вид энергии получают в основном на ТЭС, АЭС и ГЭС, то тепловую энергию поставляют потребителям централизованно (от ТЭЦ и крупных котельных) и ...
Бабенко, Ольга Анатольевна +2 more
core +1 more source
Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions
Advanced Engineering Materials, EarlyView.This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel +6 more
wiley +1 more source