Results 61 to 70 of about 161,609 (256)

Analysis of Thermo-physical Properties’ Influence Rules on Vehicular Twin-tube Shock Absorber

工程科学与技术, 2011
:The oil leakage under too high temperature which occurred in the course of shock absorber’s work process is not only a key problem which troubled the reliability design of the shock absorber, but also one of important factors to affect the vehicle ride.
Yao Ming-tao
doaj  

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Thermo-physical properties of diamond nanofluids: A review

International Journal of Heat and Mass Transfer, 2019
Abstract Nanofluids offer many opportunities to enhance the efficiency of thermal systems by improving the thermal properties of the host fluids. Due to its exceptional thermal, mechanical and electrical properties, diamond has attracted attention for use as a nanoparticle in fluids.
Farzin Mashali, Ethan Mohseni Languri, Jim Davidson, David Kerns, Wayne Johnson, Kashif Nawaz, Glenn Cunningham   +6 more
openaire   +2 more sources

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Activated carbon from thermo-compressed wood and other lignocellulosic precursors

BioResources, 2007
The effects of thermo-compression on the physical properties such as bulk density, mass yield, surface area, and also adsorption capacity of activated carbon were studied.
Capart, R., Ould-Dris, A., Khezami, L.
doaj  

ANALYSIS OF THE APPLICATIONS OF THE DATA-DRIVEN APPROACH IN EVALUATING THE THERMAL-PHYSICAL PROPERTIES OF COMPOSITES

Вісник Національного технічного університету "ХПÌ": Системний аналіз, управління та інформаційні технології
This research analyzes the potential and prospects of a data-driven methodology for examining the thermo-physical properties of composite materials. The research is to provide an analysis of the potential and benefits of employing data-driven procedures,
Ruslan Lavshchenko, Gennadiy Lvov
doaj   +1 more source

The Effect of Few-Layer Graphene on the Complex of Hardness, Strength, and Thermo Physical Properties of Polymer Composite Materials Produced by Digital Light Processing (DLP) 3D Printing. [PDF]

Materials (Basel), 2023
Kidalov S, Voznyakovskii A, Vozniakovskii A, Titova S, Auchynnikau Y.   +4 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Modelling of the Thermo-Physical and Physical Properties for Solidification of Al-Alloys [PDF]

, 2016
The thermo-physical and physical properties of the liquid and solid phases are critical components in casting simulations. Such properties include the fraction solid transformed, enthalpy release, thermal conductivity, volume and density all as a function of temperature.
N. Saunders, X. Li, A. P. Miodownik, J.-P. Schille   +3 more
openaire   +1 more source