Results 11 to 20 of about 3,000,384 (294)
Thermomechanical Processing of Steels [PDF]
Metals, 2020 The combination of hot working technologies with a thermal path, under controlled conditions (i [...]
Pello Uranga +1 more
doaj +9 more sources
Optimizing Thermomechanical Processing of Bimetallic Laminates. [PDF]
Materials (Basel), 2023 Thermomechanical processing combining plastic deformation and heat treatment is a favorable way to enhance the performance and lifetime of bimetallic laminates, especially those consisting of metals, which tend to form intermetallic layers on the interfaces when produced using methods involving increased temperatures.
Kocich R.
europepmc +6 more sources
Metals, 2022 The effects of thermomechanical processing on the microstructure and hydrogen embrittlement properties of ultrahigh-strength, low-alloy, transformation-induced plasticity (TRIP)-aided bainitic ferrite (TBF) steels were investigated to apply to automobile
Tomohiko Hojo +8 more
doaj +2 more sources
Influence of thermomechanical processing regime on the mechanical properties and electrical conductivity of PdNi5 alloy [PDF]
Hemijska Industrija, 2017 This paper deals with experimental and analytical investigations of the influence of thermomechanical processing conditions on the mechanical properties and electrical conductivity of PdNi5 alloy, in the form of wire Ø 0.15 mm, for making catalysts ...
Cvetković-Stamenković Vesna V. +6 more
doaj +3 more sources
The Influence of Thermomechanical Treatments on the Mechanical Properties of Some Al-Zn-Mg-Cu Alloys [PDF]
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials ScienceIn this paper, the variation of some mechanical properties was studied according to the values of the thermomechanical processing parameters to which an aluminium alloy of the Al-Zn-Mg-Cu series was subjected.
Marian-Iulian NEACȘU
doaj +2 more sources
International Journal of Nanomedicine, 2015 Mohsin Talib Mohammed,1 Zahid A Khan,1 Geetha Manivasagam,2 Arshad N Siddiquee1 1Mechanical Engineering Department, Faculty of Engineering, Jamia Millia Islamia, New Delhi, 2Centre for Biomaterials Science and Technology, VIT University, Vellore, India
Mohammed MT +3 more
doaj +1 more source
Optimization of Thermomechanical Processing of Some Aluminum Alloys by Dimensional Interpolation Method Using the Matlab [PDF]
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2013 This paper presents results of research on optimization of thermomechanical treatment applied to an alloy of the Al-Zn-Mg-Cu system, used in the aviation industry.
Marian NEACSU +2 more
doaj +1 more source
Hot deformation and dynamic α-globularization of a Ti-17 alloy: Consistent physical model
Materials & Design, 2021 Ti-17 is exposed to microstructural modifications during thermomechanical treatment. In this work, we focus on the characterisation, analysis and modelling of the modifications during plastic deformation in the one phase and two phases domain.
Ricardo Henrique Buzolin +3 more
doaj +1 more source
Journal of Magnesium and Alloys, 2023 This work explores the correlation between the characteristics of the cast structure (dendrite growth pattern, dendrite morphology and macro-texture) and strain hardening capacity during high temperature deformation of Mg-5Sn-0.3Li-0 and 3Zn multi ...
MS. Jalali +7 more
doaj +1 more source
Journal of Materials Research and Technology, 2022 The present study deals with the extraordinary twin formation during compressive deformation of a Fe-37.55Mn-8.5Al-0.6C (wt.%) low-density steel at warm temperature regime (200–600 °C). Despite the conventional opinion regarding the restrictive effect of
Rezvan Khani +4 more
doaj +1 more source