Results 21 to 30 of about 11,624 (301)

The effect of rare earth elements on the work softening behavior of as-cast Mg-4Al-2Sn

Materials Research Express, 2020
This work explores the addition of 1% Rear Earth (RE) elements on the Mg–4Al–2Sn magnesium alloy, with an emphasis laid on the microstructural evolution during solidification and subsequent hot deformation behavior.
M S Jalali, A Zarei-Hanzaki, A M Jamili, H R Abedi, M Mosayebi, S M Vakili   +5 more
doaj   +1 more source

The high temperature deformation behavior of a triplex (ferrite+ austenite+ martensite) low density steel

Journal of Materials Research and Technology, 2021
The present work deals with the high temperature deformation behavior of Fe-11.15Mn-5.6Al-0.07C (wt.%) triplex ferrite-based lightweight steel in the temperature range of 800–1100 °C under the strain rate of 0.001 to 0.1s−1.
Amir-Reza Kalantari, Abbas Zarei-Hanzaki, Hamid Reza Abedi, Mohammad Sadegh Jalali, Seong-Jun Park, Jun Young Park   +5 more
doaj   +1 more source

The effect of thermomechanical processing on the piezoelectric and electrical conductivity of PLA/2.5%MWCNT composite

Journal of Materials Research and Technology, 2023
The electrical properties of polymer materials, such as electrical conductivity and piezoelectricity, are significantly influenced by the ratio of amorphous to crystalline regions. Additionally, the alignment of added particles and formed crystallites is
Sahar Shahparvar, Abbas Zarei-Hanzaki, Amirhossein Farahani, Roohollah Bagherzadeh, Hamid Reza Abedi   +4 more
doaj   +1 more source

Harmonizing sound and light: X-ray imaging unveils acoustic signatures of stochastic inter-regime instabilities during laser melting

Nature Communications, 2023
Laser powder bed fusion (LPBF) is a metal additive manufacturing technique involving complex interplays between vapor, liquid, and solid phases. Despite LPBF’s advantageous capabilities compared to conventional manufacturing methods, the underlying ...
Milad Hamidi Nasab, Giulio Masinelli, Charlotte de Formanoir, Lucas Schlenger, Steven Van Petegem, Reza Esmaeilzadeh, Kilian Wasmer, Ashish Ganvir, Antti Salminen, Florian Aymanns, Federica Marone, Vigneashwara Pandiyan, Sneha Goel, Roland E. Logé   +13 more
doaj   +1 more source

The correlation of austenite stability and sequence of strain accommodation during room temperature deformation of a duplex lightweight steel

Journal of Materials Research and Technology, 2021
The effect of austenite stability on the sequence of room temperature strain accommodation has been investigated in Fe-0.07C-11.15Mn-5.6Al-0.12Si lightweight steel through employing interrupted tensile tests coupled with electron backscattered ...
B. Mirshekari, A. Zarei-Hanzaki, A. Barabi, H.R. Abedi, S.-J. Lee, H. Fujii   +5 more
doaj   +1 more source

Evolution of precipitates, in particular cruciform and cuboid particles, during simulated direct charging of thin slab cast vanadium microalloyed steels [PDF]

, 2004
A study has been undertaken of four vanadium based steels which have been processed by a simulated direct charging route using processing parameters typical of thin slab casting, where the cast product has a thickness of 50 to 80mm ( in this study 50 mm)
Carven, A.J., Baker, T,N,, Crowther, D.N., Baker, T.N., Li, Y., Wilson, J.A., Craven, A.J.   +6 more
core   +1 more source

Experimental investigation of the influence of the FSW plunge processing parameters on the maximum generated force and torque [PDF]

, 2010
The paper presents the results of an experimental investigation, done on the friction stir welding (FSW) plunging stage. Previous research works showed that the axial force and torque generated during this stage were characteristic for a static ...
ZIMMER-CHEVRET, Sandra, LANGLOIS, Laurent, LAYE, Julien, BIGOT, Régis   +3 more
core   +1 more source

Experimental study of the brittle–ductile transition in hot cutting of SG iron specimens [PDF]

, 2013
http://www.sciencedirect.com/science/article/pii/S0924013612002579The present paper investigates the brittle-ductile transition (BDT) of the primary shear zone during cutting of spheroidal graphite (SG) iron in the austenitization temperature range ...
EL MANSORI, Mohamed, FOUILLAND-PAILLE, Laurence, Fouilland, Laurence   +2 more
core   +1 more source

Twin-based martensite stabilizing and improving the shape memory response of near equiatomic NiTi alloy through multi-axial forging

Journal of Materials Research and Technology, 2022
In the present study, a high cumulative true strain (∼4.5) was applied on a near equiatomic NiTi shape memory alloy through multi-axial forging in the course of “isothermal” and “continuous cooling” regimes.
A. Shamsolhodaei, A. Zarei-Hanzaki, H.R. Abedi, A. Safdel, M. Peterlechner   +4 more
doaj   +1 more source

Mapping of mechanical, thermomechanical and wire-bond strain fields in packaged Si integrated circuits using synchrotron white beam x-ray topography [PDF]

, 2001
Thermal processing steps used during the production of packaged integrated circuits can lead to severe thermomechanical stresses. In addition, the process of bonding wires to contact pads can also lead to strain field generation.
McNally, Patrick J., Herbert, P.A.F., Lowney, D., Danilewsky, A. N., Rantamäki, Raija, Curley, John W., Herbert, P. A. F., Tuomi, Turkka O., Curley, J. W., Lowney, Donnacha, Rantamäki, R., Tuomi, T., Danilewsky, Andreas N., Danilewsky, Andreas, McNally, P. J., Tuomi, Tiinamaija   +15 more
core   +1 more source