Results 201 to 210 of about 11,624 (301)

Effect of recycling on mechanical and physical properties of polycarbonate/acrylonitrile–butadiene–styrene/poly(methyl methacrylate) (PC/ABS/PMMA) blends

Polymer International, EarlyView.
The 100% recycling of optimal polycarbonate/acrylonitrile–butadiene–styrene/poly(methyl methacrylate) (PC/ABS/PMMA) blends, identified through the mixture design, over multiple successive cycles provides valuable insights into their life cycle. Subsequently, chemical, rheological, thermal and mechanical characterizations will be carried out to evaluate
Rahma Ezzeddine, Karama Elfehri, Ángel Marcos‐Fernández, Basma Samet   +3 more
wiley   +1 more source

Thermomechanical processing in titanium alloys.

Bulletin of the Japan Institute of Metals, 1986
openaire   +2 more sources

High‐strength composites by thiocracking of high‐polypropylene‐content mixed waste

Polymer International, EarlyView.
Mixed plastic waste made up of polystyrene and polypropylene was reacted with elemental sulfur to give high‐strength composites. Abstract Mixed‐material municipal waste poses a persistent end‐of‐life management challenge because the heterogeneous composition limits efficient separation and recycling. After disposal, mixed‐material waste often fragments
Athira Babu, Rhett C. Smith
wiley   +1 more source

Study of the Influence of Thermomechanical Treatment on the Structure and Properties of Zircalloy-4 Alloy. [PDF]

Materials (Basel)
Popov F, Kawalek A, Ozhmegov K, Lutchenko N, Panin E, Lezhnev S, Arbuz A.   +6 more
europepmc   +1 more source

Shingle Interconnection Reliability of PERC and Thin HJT Cells for Low Earth Orbit Applications

Progress in Photovoltaics: Research and Applications, EarlyView.
Evolution of maximum power output (Pmax$$ {}_m ax $$) of PERC and thin HJT shingled cells with the Electrically Conductive Adhesives (ECA) “S” and “A” exposed to +120°C/−$$ - $$120°C thermal cycles up to 5×103$$ 5\times 1{0}^3 $$ times. Losses are induced by an increased series resistance with all cell technologies and ECA. Imaging (electroluminescence
Jean‐Baptiste Charpentier, Clément Jamin, David Veyrié, Matthieu Fongral, Vincent Barth, Philippe Voarino   +5 more
wiley   +1 more source

Al/SiCp Composites Behavior During Thermomechanical Processing

Science and Engineering of Composite Materials, 1997
Severin, Irina, Zgura, Gheorghe, Marinescu, loan D.   +2 more
doaj   +1 more source

Editorial for the Special Issue "Research on Performance Improvement of Advanced Alloys". [PDF]

Materials (Basel)
Quan G, Yu C.
europepmc   +1 more source

Application of Non‐Isothermal Network Theory With Curved‐Channel Element Characteristics to Predict Melt Conveying in High‐Performance Single‐Screw Extruders

Journal of Polymer Science, EarlyView.
This study presents a fast and accurate calculation tool to predict conveying of polymer melts in single‐screw extruders. Integrating generalized sub‐models into network theory allows to represent the complex screw shapes and material behavior more realistically. Tests on an industrial extruder show close agreement with experiments, outperforming older
Daniel Herzog, Wolfgang Roland, Christian Marschik, Gerald Berger‐Weber   +3 more
wiley   +1 more source

High-Performance PA6 Composites Reinforced with Recycled Aramid Fibers from Firefighter Protective Clothing. [PDF]

Polymers (Basel)
Marco-Sanjuan J, Lazaro-Herdez C, Miranda-Pinzon M, Fenollar O.   +3 more
europepmc   +1 more source

Conjugated Polymers Engineered for Flexible/Stretchable Electronics

Journal of Polymer Science, EarlyView.
This review highlights glass transition temperature (Tg) as the central parameter linking molecular structure to device performance in conjugated polymers. By tuning backbone rigidity, side‐chain architecture, and dynamic bonding, Tg governs the balance between π–π stacking–enabled charge transport and mechanical compliance.
Yunchong Yang, Josh Bass, Weijia Yan, Ashwath Anand, Chunka Zhou, Jingjing Qiu   +5 more
wiley   +1 more source