Results 121 to 130 of about 6,190 (262)

Effect of Ni/Si Mass Ratio and Thermomechanical Treatment on the Microstructure and Properties of Cu-Ni-Si Alloys. [PDF]

Materials (Basel), 2019
Li J, Huang G, Mi X, Peng L, Xie H, Kang Y.   +5 more
europepmc   +1 more source

Melt and Cold Crystallization Behavior of Poly(Lactic Acid) With Different Molecular Weights and Its Influence on Mechanical, Viscoelastic, and Tribological Properties

Polymer Engineering &Science, EarlyView.
Modifying the crystallinity of PLA and its properties through annealing. ABSTRACT The melt and cold crystallization behavior of two PLA grades with different molecular weights was investigated using various DSC analyses. During isothermal melt crystallization, PLA with lower molecular weight exhibited faster crystallization kinetics across different ...
Rio M. Mungok, Joel Y. Vidua, Ulrich A. Handge   +2 more
wiley   +1 more source

Experimental investigation of mechanical properties of sustainable silica sand reinforced AA6061 composites subjected to thermomechanical treatment. [PDF]

Sci Rep
Sadanand RV, Nayak SY, Prabhu A.
europepmc   +1 more source

On the Thermomechanical Treatment of Steel

Tetsu-to-Hagane, 1966
openaire   +2 more sources

Ultrasound‐Assisted Epoxy Resin Curing Monitored by Impedance Spectroscopy

Polymer Engineering &Science, EarlyView.
Ultrasound enhances epoxy cure rates via localized heating without altering cure kinetics. Impedance spectroscopy provides a direct, non‐destructive measure of cure progression, enabling accurate mapping of degree of cure in real time. ABSTRACT Epoxy resins are widely used in aerospace and automotive manufacturing as structural adhesives and matrices ...
Daniel Csehngeri, Anoush Poursartip, Edmond Cretu   +2 more
wiley   +1 more source

Improvement of Microstructure and Mechanical Properties of a Hot-Extruded Cu-Al₂O₃ Alloy After Thermomechanical Treatment. [PDF]

Materials (Basel)
Wang X, Pan X, Liu P, Xiao Z, Zhou T, Gan C, Wang J.   +6 more
europepmc   +1 more source

Comparing the Applicability of State‐Of‐The‐Art Photopolymer Injection Molds Printed by Multi‐Material Jetting and High‐Performance Digital Light Processing

Polymer Engineering &Science, EarlyView.
The workflow of comparing state‐of‐the‐art photopolymers in rapid tooling. ABSTRACT Additive manufacturing (AM) introduced the concept of layer‐by‐layer manufacturing, which allows the fast and direct production of parts. Additive technologies are also hybridized with conventional polymer processing technologies.
Szabolcs Krizsma, András Suplicz
wiley   +1 more source

Improvement in Grain Size Distribution Uniformity for Nuclear-Grade Austenitic Stainless Steel through Thermomechanical Treatment. [PDF]

Materials (Basel)
Wang Y, Xue W, Pang Z, Zhao Z, Liu Z, Liu C, Gao F, Li W.   +7 more
europepmc   +1 more source

Erosion Resistance Enhancement in Epoxy Composites by Recycled Rubber: Effect of Rubber Type

Polymer Engineering &Science, EarlyView.
Erosion resistance enhancement in epoxy composites by recycled rubber. ABSTRACT Epoxy‐based materials have low erosion resistance due to their brittle nature, and toughness modification stands out for enhancing it. At this stage, the use of waste rubber as a reinforcement component in the composite system is of interest due to its role in providing ...
Orkan Baran Korkusuz, Şehriban Öncel, Bağdagül Karaağaç, Tamer Sınmazçelik   +3 more
wiley   +1 more source

Effect of post-weld heat-treatment and solid-state thermomechanical treatment on the properties of the AA6082 MIG welded joints. [PDF]

Sci Rep
El-Fahhar HH, Gadallah EA, Habba MIA, Seleman MME, Ahmed MMZ, Mohamed AY, Fouad RA.   +6 more
europepmc   +1 more source