Results 111 to 120 of about 850,081 (283)

Materials‐Driven Additive Manufacturing for Electrical Machines: Qualification‐Oriented Design Beyond Geometric Freedom

Advanced Engineering Materials, EarlyView.
This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley   +1 more source

Development of an anchor system for thick CFRP plates: Experimental and numerical investigation

Case Studies in Construction Materials
Carbon fiber reinforced polymer (CFRP) has been widely used in construction, rehabilitation and maintenance of civil infrastructures. Anchor system is one of the most crucial part ensuring load transfer between CFRP and the structures.
Cheng Tan, Xu Jiang, Xuhong Qiang, Song Han, Xu Ren, Jiazhan Xie   +5 more
doaj   +1 more source

FastNano Liquid: An Automated Platform for Small‐Angle X‐ray Scattering‐Based Materials Discovery

Advanced Engineering Materials, EarlyView.
We present FastNano Liquid, an automated small‐ and wide‐angle X‐ray scattering platform for the combined synthesis and characterization of (nano)materials. The platform is coupled to varied reactor workflows for both in situ studies of reaction kinetics and ex situ screening of synthesis conditions to support machine learning‐guided exploration ...
Pierre‐Baptiste Flandrin, Émeline Cournède, Jens Krarup, Michael Lesa, Foyzul Hasan, Amandine Séné, Arnaud Lahouati, David Benhaiem, Jérémie‐Luc Sanchez, Simon Delacroix, Thierry Gacoin, Fabienne Testard, Damien Faivre, David Carriere, Corinne Chevallard, Olivier Taché, Mark A. Levenstein   +16 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

ANALYSIS OF THICK RECTANGULAR PLATES RESTING ON NONLINEAR WINKLER FOUNDATION

Journal of Engineering and Sustainable Development, 2016
This research deals with the elastic behavior of thick plates resting on nonlinear Winkler foundation. Mindlin’s thick plate theory is extended to include the effect of nonlinear elastic foundation.
Adel A. Al-Azzawi, Hasanain M. Ghaltan
doaj  

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

Advanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika, Hunter Kantelis, Yogesh K. Vohra, Shengbiao Zhang, Wuxian Yang, Wen Chen   +5 more
wiley   +1 more source

Printed Integrated Logic Circuits Based on Chitosan‐Gated Organic Transistors for Future Edible Systems

Advanced Functional Materials, EarlyView.
Edible electronics needs integrated logic circuits for computation and control. This work presents a potentially edible printed chitosan‐gated transistor with a design optimized for integration in circuits. Its implementation in integrated logic gates and circuits operating at low voltage (0.7 V) is demonstrated, as well as the compatibility with an ...
Giulia Coco, Valerio Francesco Annese, Valerio Galli, Ilaria Penna, Debora Russo, Marina Veronesi, Rita Scarpelli, Stefania Sabella, Mario Caironi   +8 more
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source