Results 41 to 50 of about 233,358 (261)
FEBS Open Bio, EarlyView.Miniaturized flow chip platform enabling continuous perfusion and longitudinal multiphoton 3D imaging of vascular smooth muscle cell constructs under physiological flow. Brightfield imaging guides region selection, while CellTracker Green and mRuby‐labeled fetuin‐A visualize cells and mineral deposition, respectively. Magnesium supplementation markedly
Vytautas Kučikas +6 more
wiley +1 more source
Malformin A1–mediated cytotoxicity in ovarian cancer cells occurs through pyroptosis and autophagy
FEBS Open Bio, EarlyView.This study investigated the effects of the natural compound Malformin A1 (MA1) on the cytoskeleton that regulates cell proliferation and migration. Disruption of the cytoskeleton can impair these processes and promote cancer cell death. MA1 disrupted cytoskeletal organization, induced DNA damage, inflammation, activated autophagy, and pyroptosis ...
Nada Abdullah Hassan +11 more
wiley +1 more source
International Journal of Polymer Science, 2016 This paper presented a durability experimental study for thin basalt fiber reinforced polymer (BFRP) mesh reinforced cementitious plates under indoor and marine environment.
Yan Xie, Kunhua Guan, Lin Lai
doaj +1 more source
Metals, 2020 In this work, an improved explosive welding technique was investigated to fabricate a thin Mg/Al plate, where an additional thin aluminum sheet was used as a buffer layer between the explosive and the Al plate, and the Mg plate was rigidly constrained by
Qi Wang, Xuejiao Li, Biming Shi, Yong Wu
doaj +1 more source
Advanced Engineering Materials, EarlyView.In this review, the current state of light‐assisted 3D printing as it pertains to engineering musculoskeletal tissues including bone, cartilage, skeletal muscle, tendon, and ligaments is summarized. Common printing techniques, photoreactive materials, and study design choices are compiled and reviewed.
Meagan Morgan, Bin Zhang, Roger Narayan
wiley +1 more source
Derivation of losses from impedance spectrum for contour modes of ceramic resonator
Journal of Asian Ceramic Societies, 2020 Method of loss coefficients calculation from mechanical quality factors of transversal vibration modes is presented. Theoretical formulae are derived for the contour mode of thin square plate and width extensional mode of a thin rectangular plate ...
Jiří Erhart +3 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal +2 more
wiley +1 more source
R-Function and variation method for bending problem of clamped thin plate with complex shape
Advances in Mechanical Engineering, 2021 Solving ordinary thin plate bending problem in engineering, only a few analytical solutions with simple boundary shapes have been proposed. When using numerical methods (e.g.
Fengfei Xia, Shanqing Li
doaj +1 more source