Results 91 to 100 of about 2,754 (221)

Effect of Process Parameters on the Mechanical Properties of Simultaneous Double-Sided Friction Stir Welding Joints

Chinese Journal of Mechanical Engineering
Currently, conventional single-sided friction stir welding is primarily suitable for joining thin plate aluminum alloys, and its application to thick plates is still challenging in terms of welding efficiency and joint mechanical properties. Simultaneous
Shaofei Meng, Huihui Zhao, Jiyi Dong, Wu Liu, Haitao Liu, Juliang Xiao   +5 more
doaj   +1 more source

Nonwoven rCF/PA6 Thermoplastic Composites: Hybrid Commingled Fibers vs. Powder Impregnation—Effects on Microstructure and Mechanical Properties

Polymer Composites, EarlyView.
Comparison of powder impregnation and hybrid commingled non‐wovens for PA6/rCF nonwoven composites. The two‐step powder route gives lower voids and higher properties, while the single‐step hybrid route is limited by precursor inhomogeneity and high void content.
Gaia Francesca Lupia, Tommaso Pini, Ilaria Rossitti, Sara Taherinezhad Tayebi, Marco Valente   +4 more
wiley   +1 more source

Analysis of the Interfacial Bond Strength in Overmoulded Thermoplastic Composites

Polymer Composites, EarlyView.
Two‐step injection overmoulding process investigated in this work, showing selective gate injection over a 450 mm demonstrator beam to vary flow length and rib pull‐off mechanical testing with fractographic characterisation of the overmoulded interface.
Casilda S. Villalobos, Samson Gnanadass, Jaipal Gupta, Neill Raath, Neil Reynolds, Ton Peijs   +5 more
wiley   +1 more source

Variable Polarity Arc Welding of Aluminum Thin Plate

Journal of the Korean Society of Manufacturing Process Engineers, 2014
ABSTRACT Variable polarity (VP) arc welding is known as an effective solution foraluminum thanks to thecleaning effect, which means oxide removal, during theDCEP (direct current electrode positive) period. In this research, VP GTAW (gas tungsten arc welding) is adopted for lap joint fillet welding of 3mm thickness 5052 aluminum alloy.
openaire   +2 more sources

Process‐Induced Anisotropy and Fracture Behavior of Pellet‐3D Printed PLA and PLA/Flax Biocomposites

Polymer Composites, EarlyView.
Fused Granular Fabrication of PLA and PLA/flax biocomposites, followed by tensile testing and fracture surface analysis to evaluate the effects of raster orientation and layer number on anisotropy and fracture behavior. ABSTRACT Fused granular fabrication (FGF) enables cost‐effective, large‐scale polymer additive manufacturing; however, the mechanical ...
Fernando Ancio, Luis Távara, Luis Miguel Ferreira   +2 more
wiley   +1 more source

Effect of Accelerated Aging on the Performances of 3D Printed Polylactic Acid‐Polyhydroxyalkanoate Specimens

Polymer Engineering &Science, EarlyView.
The accelerated aging behaviours on the FFF‐fabricated PLA‐PHA Specimens. ABSTRACT Despite the increasing use of biodegradable polymers in additive manufacturing, their long‐term durability remains insufficiently understood. The aim of this study to investigate the influence of accelerated aging on the performance of fused filament fabrication‐printed ...
Han Xu, Jiayu Chen, Yinshi Lu, Handai Liu, Farnoosh McDonagh, Evert Fuenmayor, Ian Major, Genfu Xiao, Ke Gong   +8 more
wiley   +1 more source

Enhancing PET Printability via Solid‐State Polymerization: Structure‐Processing‐Properties Relationships

Polymer Engineering &Science, EarlyView.
Solid‐state polymerization (SSP) enhances rheological properties, filament stability, and adjusts crystallization issues for improved PET 3D printability. ABSTRACT This paper aims to investigate the impact of solid‐state polymerization (SSP) on the printability of PET for 3D printing.
Benjamin Sandei, Noah Nohadani, Cécile Nouvel, Valérie Massardier‐Nageotte, Claire Barrès, Mohamed Yousfi   +5 more
wiley   +1 more source

Actuation Strategies for Underwater Jet‐Propelled Soft Robots

Journal of Field Robotics, EarlyView.
ABSTRACT This review article examines jet‐propulsion mechanisms in underwater soft robotic systems, focusing exclusively on physically fabricated and experimentally validated robots. Covering research published from 2013 to 2025, this study classifies and evaluates jet‐propulsion robots based on their actuation mechanisms.
Angel Kitone, Mohammed Anteet, Pawandeep S. Matharu, Yara Almubarak   +3 more
wiley   +1 more source

Hierarchically Biporous Wick Vapor Chamber With Micro/Nano Condenser for Exceeding 600 W/cm2 Heat Dissipation

Small, EarlyView.
An integrated vapor chamber couples a hierarchically biporous copper wick with a micro/nano‐textured superhydrophobic condenser to form a self‐sustained liquid–vapor loop. The device dissipates extreme heat fluxes above 600 W/cm2, even when the condenser is above the heater, by overcoming the permeability‐capillarity trade‐off in conventional vapor ...
Ya‐Nan Li, Run‐Sheng Qi, Yawen Shi, Zeng‐Yao Li, Xinpeng Zhao   +4 more
wiley   +1 more source

Physical Anchoring‐Assisted Mechanically Guided Assembly for Material‐Independent 3D Mesostructures

Small, EarlyView.
Conventional mechanically guided 3D assembly relies on selective chemical bonding between 2D precursors and elastomeric substrates, imposing fundamental limitations on material compatibility and scalability. Here, we present a physically anchored, buckling‐guided assembly platform based on a rod array patterned elastomeric substrate (RPES).
Yeonhee Heo, Pei Liu, Jeongmin Yoo, Jae Hyuk Hwang, Gooyoon Chung, Dong‐Gyun Kim, Raudel Avila, Yoonseok Park   +7 more
wiley   +1 more source