Results 21 to 30 of about 178,517 (320)
Programmable material testing device for mechanoluminescence measurements
HardwareX, 2022 Mechanoluminescent materials transform mechanical energy into visible light. Phenomena could prove to be advantageous to various next-generation monitoring systems employed in the fields of security and healthcare if the intrinsic mechanisms are fully ...
Ernests Einbergs, Aleksejs Zolotarjovs
doaj +1 more source
Experimental composite material modified with calcium fluoride – three-point bending flexural test
Journal of Achievements of Materials and Manufacturing Engineering, 2016 B. Łapińska +6 more
openaire +2 more sources
Journal of Materials Research and Technology, 2022 Property evolution of carbon fiber reinforced epoxy composite used in marine environment was investigated in this paper. The moisture absorption and flexural properties of carbon fiber composite laminate were studied under the combined pretreatment ...
Yansheng Fan +4 more
doaj +1 more source
Research on differences and correlation between tensile, compression and flexural moduli of cement stabilized macadam [PDF]
Fracture and Structural Integrity, 2017 In order to reveal the differences and conversion relations between the tensile, compressive and flexural moduli of cement stabilized macadam, in this paper, we develop a new test method for measuring three moduli simultaneously.
Yi Yang, Jianlong Zheng, Songtao Lu
doaj +2 more sources
The Effect on the Flexural Strength, Flexural Modulus and Compressive Strength of Fibre Reinforced Acrylic with That of Plain Unfilled Acrylic Resin – An in Vitro Study [PDF]
Journal of Clinical and Diagnostic Research, 2015 Aim: The aim of this in vitro study was to compare the flexural strength, the flexural modulus and compressive strength of the acrylic polymer reinforced with glass, carbon, polyethylene and Kevlar fibres with that of plain unfilled resin.
Tony C Thomas +5 more
doaj +1 more source
Bioscience Journal, 2016 The proper mechanical properties of resin cements are essential to the longevity of indirect restoration, whereas the 3-point bending test is recommended for measuring the flexural strength.
Ana Carla Assunção Oliveira +4 more
doaj +3 more sources
Comparative Assessment of Commonly Used Concrete Damage Plasticity Material Parameters
Engineering Transactions, 2022 The non-homogeneous and non-linear mechanical behaviour of concrete complicates the numerical simulations of its corresponding material model. The concrete damaged plasticity (CDP) model is one of the most popular constitutive models for concrete. State-
Hasan AL-RIFAIE, Darbaz MOHAMMED
doaj +1 more source
The fractography analysis of IN718 alloy after three-point flexure fatigue test [PDF]
MATEC Web of Conferences, 2018 In this study, the high cycle fatigue (HCF) properties of IN718 superalloy with given chemical composition were investigated at three-point flexure fatigue test at room temperature. INCONEL alloy 718 is nickel-chromium-iron hardenable alloy and due to its unique combination of mechanical properties (high-strength; corrosion-resistant and so on) used ...
Belan Juraj +3 more
openaire +2 more sources
Calculation of measurement uncertainty for plastic (ABS) material in flexural testing [PDF]
International Journal of Metrology and Quality Engineering, 2013 In order to determine mechanical properties of materials various kind of tests can be applied by means of using their tensile strength, lower yield stress, proof stress, impact strength, Brinell, Rockwell and surface hardness, elongation after fracture ...
Gunay A. +3 more
doaj +1 more source
Dentistry Journal, 2023 Herein, the mechanical properties of an auto-polymerizing resin incorporated with a surface pre-reacted glass ionomer (S-PRG) filler were evaluated. For this, S-PRG fillers with particle sizes of 1 μm (S-PRG-1) and 3 μm (S-PRG-3) were mixed at 10, 20, 30,
Naoyuki Kaga +3 more
doaj +1 more source