Results 231 to 240 of about 1,951,835 (279)
Some of the next articles are maybe not open access.

The Traceable Calibration of Thrust Stand by Electrostatic Force

Journal of Visualized Experiments, 2022
Micro thrusters have important applications in low-frequency gravitational wave detection, satellite formation, and inter-satellite laser communication, so it is necessary to accurately measure the thrust of micro thrusters with traceability. A thrust stand is a widely used micro thrust measuring device with the advantages of high resolution and large ...
Bin, Wang   +3 more
openaire   +2 more sources

Thrust Forces in Underwater Swimming

Human Factors: The Journal of the Human Factors and Ergonomics Society, 1965
Instantaneous and mean static thrust levels were measured for eight underwater swimmers restrained in a submerged force platform. Swimming was examined barefoot and with two types of fins. The main beneficial effect of the fins was to eliminate the substantial negative thrust component associated with barefoot swimming.
R A, Christianson   +2 more
openaire   +2 more sources

Measuring Leg Thrust Forces in the Common Starling

Journal of Experimental Biology, 1996
ABSTRACT We describe the design of a force-transducing perch which measures the reaction forces of small birds taking off and landing. In common starlings, landing forces are lower than take-off forces, because the bird may decelerate prior to landing by using its wings.
, Bonser, , Rayner
openaire   +2 more sources

Design of a linear vernier permanent magnet machine with high thrust force density and low thrust force ripple

2017 IEEE International Electric Machines and Drives Conference (IEMDC), 2017
This paper introduces a novel linear vernier permanent magnet machine (H-LVPMM) with high force density and low force ripple. The permanent magnets (PMs) on secondary uses Halbach array, which can provide a larger flux density in the air gap than that of the conventional surface-mounted PMs configurations, and the primary is composed of three modules ...
Yongsheng Huo   +4 more
openaire   +1 more source

Cranial tibial thrust: A primary force in the Canine stifle

Journal of the American Veterinary Medical Association, 1983
SUMMARY A cranially directed force identified within the canine stifle joint was termed cranial tibial thrust. It was generated during weight bearing by tibial compression, of which the tarsal tendon of the biceps femoris is a major contributor, and by the slope of the tibial plateau, found to have a mean cranially directed ...
B, Slocum, T, Devine
openaire   +2 more sources

Balanced-force-control of underactuated thrust-propelled vehicles

2007 46th IEEE Conference on Decision and Control, 2007
The paper sets the basics of a control framework for underactuated thrust-propelled vehicles immersed in a fluid, with the objective of stabilizing reference trajectories either in velocity or in position.
Minh-Duc Hua   +2 more
openaire   +1 more source

Dynamic Modeling of the Thrust Force and Torque for Drilling

1992 American Control Conference, 1992
Discrete time dynamic models relating the drilling process outputs of thrust force and torque to feed input are presented in this paper. Drilling to depths of greater than a few drill diameters with conventional twist drills, the torque and thrust force tend to increase due to difficulties with chip evacuation.
R.J. Furness, C.L. Wu, A. Galip Ulsoy
openaire   +1 more source

Evaluation of Subcooled Water Thrust Forces

Nuclear Technology, 1976
Subcooled water thrust forces for use in pipe rupture analyses have been normalized with respect to an enthalpy normalization factor. This normalization is based on comparisons with thrust forces calculated using the Henry-Fauske model, and the answers are within +-3 percent in the range 300 to 2400 psia (21.1 to 168.7 kg/cm/sup 2/).
openaire   +1 more source

The Thrust Force Structure in Drilling

2009
The purpose of this work is to present investigation of the thrust force generated during drilling process. The thrust force acting on drill is the sum of three components: the cutting component, the thrust force attributed to ploughing at the chisel edge and the thrust force resulting from friction at the margin.
Sekulić, Milenko   +4 more
openaire   +2 more sources

Intelligent Modeling of Thrust Force in Drilling Process

Journal of Dynamic Systems, Measurement, and Control, 2006
In this paper, an intelligent modeling strategy for thrust force in drilling process is proposed. First of all, neural network (NN) models are developed to model the thrust force in drilling process. Second, drill head position information is included in the NN model to get better force prediction accuracy for entrance and exit drilling stages.
Ye Sheng, Masayoshi Tomizuka
openaire   +1 more source

Home - About - Disclaimer - Privacy