Results 241 to 250 of about 1,951,835 (279)
Some of the next articles are maybe not open access.
Thrust force analysis of spindle motor for HDDs
International Symposium on Power Electronics, Electrical Drives, Automation and Motion, 2006. SPEEDAM 2006., 2006This paper presents spindle motor with fluid dynamic bearing (FDB) for hard disk drives. Thrust bearing of FDB requires appropriate pressure to operate in smooth rotations. In this study, the thrust force between rotor and thrust yoke is analyzed using 3D finite element method and experimental results are compared with the simulated ...
null Jung-Moo Seo +2 more
openaire +1 more source
A miniature force probe for cold gas thrust measurements
Review of Scientific InstrumentsThe rapid growth of the space industry is driving the development of electric propulsion systems spanning thrust from hundreds of mN down to the μN range. Conventional plume diagnostic tools are limited by size and versatility, with them being difficult to adapt across testing facilities and thrusters. Moreover, plasma-based sensors, such as Faraday or
G. Brandi +3 more
openaire +2 more sources
THRUST FORCE OF TFLM AS A DIRECTION OF FRICTIONAL RESISTANCE
International Journal of Modern Physics B, 2006This paper presents an integrated linear actuator combined with a Traverse Flux Linear Motor (TFLM) for household electric applications. They both use the same primary magnetic circuit, but they have different secondary movers. The paper presents a new design of linear motor for a new electromagnetic linear actuator, an integrated TFLM. The calculated
BYUNG-CHUL WOO +2 more
openaire +1 more source
Optimum thrust trajectories in general central force fields
Astrodynamics Conferece, 1978The well known "primer theory" of Lawden is used for the analysis of optimal coplanar orbital transfers in general central force fields. Two first-integrals, which hold for singular thrusting arcs as well as impulsive thrusts, are shown to become linearly dependent if a circular coasting arc forms part of an optimal trajectory.
openaire +1 more source
Evaluation of Thrust Force and Cutting Torque in Reaming
1996Reaming is a process that is widely used in industry with very little theoretical modelling being carried out. In this paper the cutting action of the reaming operation is presented by explaining the thrust and torque involved. A model based on an orthogonal theory of machining and variable flow stress is presented in order to predict the thrust and ...
R. Narimani, P. Mathew
openaire +1 more source
Thrust force requirements for TBMs in squeezing ground
Tunnelling and Underground Space Technology, 2010Rapidly converging ground may exert such a high pressure on the shield that the thrust force is no longer sufficient to overcome shield skin friction and the TBM becomes jammed. This paper advances a number of theory-based decision aids, which will support rapid, initial assessments to be made of thrust force requirements.
M. Ramoni, G. Anagnostou
openaire +1 more source
Increased Jet Thrust from Pressure Forces
Journal of the Aeronautical Sciences, 1950For ram-jets and turbojets, which operate with low overall jet expansion ratios, it is possible to obtain more thrust with incomplete expansion in the jet nozzle utilizing both pressure and momentum forces than with complete expansion utilizing momentum forces alone.
openaire +1 more source
Analytical modeling of thrust force and torque in drilling
Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 2013The prediction of thrust force and torque in drilling remains a key issue. There are three main ways to determine these forces based on experimental, numerical and finally analytical approaches. The major drawback with numerical and analytical methods concerns their reliability compared to phenomenological models.
Naisson, Pierre +2 more
openaire +2 more sources
Prediction of thrust forces in tubular induction machines
IEEE Transactions on Magnetics, 1992Standstill forces on tubular induction machines are calculated by two methods: a simple one-dimensional technique and a two-dimensional axisymmetric finite element analysis. The end effect force produced by the finite length of the machine is calculated. The work is confirmed by tests taken on a practical machine. >
J.F. Eastham +3 more
openaire +1 more source
2023 International Conference on Smart Energy Systems and Technologies (SEST), 2023
Reza Jafari +3 more
openaire +1 more source
Reza Jafari +3 more
openaire +1 more source

