Results 121 to 130 of about 355,851 (216)

Study of flow stress and spall strength of additively manufactured Ti-6-4 alloy

EPJ Web of Conferences, 2018
The use of additive manufacturing (AM) by Electron Beam Melting (EBM) or Selective Laser Melting (SLM) has extensively grown in the past few years.
Paris Vitaly, Cohen Amitai, Gudinetsky Eli, Hevroni Refael, Samuha Shmuel, Osovsky Shmuel, Tiferet Eitan, Yosef-Hai Arnon   +7 more
doaj   +1 more source

Secondary machining characteristics of additive manufactured titanium alloy Ti-6Al-4V [PDF]

, 2018
© 2018 Trans Tech Publications, Switzerland Titanium alloy, Ti-6Al-4V is a popular alloy used in wide range of design applications mostly in aerospace and biomedical industry due to its advantageous material properties.
G Littlefair (9877661), A Polishetty (9877664), B Raju (7805369)   +2 more
core  

Microstructure and mechanical property improvement of concurrent wire-powder feeding laser melting deposition Ti-6Al-4V via TiC addition

Materials Research Express
Wire-feed laser metal deposition (LMD-W) offers a high deposition rate and low cost, making it an effective solution for reducing costs and enhancing efficiency in manufacturing large-scale titanium aerospace components.
Chenyang Wang, Fei Xing, Xiangyu Liu, Hongyou Bian, Weijun Liu   +4 more
doaj   +1 more source

Brazeability, Microstructure, and Joint Characteristics of ZrO2/Ti-6Al-4V Brazed by Ag-Cu-Ti Filler Reinforced with Cerium Oxide Nanoparticles

Advances in Materials Science and Engineering, 2019
In this work, we have attempted to develop the Ag-Cu-Ti filler for bonding ZrO2 to Ti-6Al-4V. The CeO2 nanoparticles were reinforced in the eutectic Ag-Cu-Ti filler via mechanical mixing and melting route.
Ashutosh Sharma, Byungmin Ahn
doaj   +1 more source

Corrosion behavior of Ti-6Al-4V by 3D printing techenology in the airfield pavement deicing fluid

四川大学学报. 自然科学版, 2020
In this paper, we study the corrosion of the Ti-6Al-4V alloy prepared by electron beam printing (EBM) and laser melt printing (SLM) technology by runway de-icing chemicals (potassium acetate solution).
CHEN Ai-Jun, DENG Hao, CHEN Long-Qing, TANG Yi, TANG Jun   +4 more
doaj  

Microstructures and surface roughness of EBM produced Ti-6Al-4V [PDF]

, 2010
The work presented in this dissertation is concerned with the microstructures and surface roughness of test slabs of Ti-6Al-4V produced by one of powder based Additive Manufacturing (AM) technique namely Electron Beam melting (EBM).
Adnan, Safdar, Safdar, Adnan
core  

Fatigue Behavior of Hybrid Additive/Subtractive Manufactured Ti-6Al-4V

Metals
Additive–subtractive hybrid manufacturing (ASHM) allows for the rapid manufacturing of metal components with complex and precise geometries for ready-to-use or near-ready-to-use applications.
Nicholas Parolini, Andrew Ikeler, Ryan Kinser, Abhendra Singh, P. G. Allison, J. B. Jordon   +5 more
doaj   +1 more source

Microstructure and texture development during solid consolidation recycling of Ti-6Al-4V [PDF]

, 2018
Ti-6Al-4V machining chips were recycled using equal channel angular pressing (ECAP). The microstructural and texture evolution of the recycled Ti-6Al-4V have been investigated using scanning electron microscopy, electron backscattered diffraction and ...
Qi (Alex) Shi (7124834), Yau Tse (1249800), Rebecca Higginson (1252992)   +2 more
core  

Crystallographic variant selection in Ti-6Al-4V [PDF]

, 2004
Transformation textures in the two-phase alloy Ti–6Al–4V have been studied. Samples were heated into the fully β phase condition and then slow cooled to allow diffusional transformation to α.
N Stanford (13285038), P Bate (13285041)
core  

Additive manufacturing of Ti-6Al-4V alloy- A review

Journal of Materials Research and Technology, 2022
Hung Dang Nguyen, A. Pramanik, A. K. Basak, Y. Dong, C. Prakash, S. Debnath, S. Shankar, I. Jawahir, Sourav Dixit, D. Buddhi   +9 more
semanticscholar   +1 more source