Ti-6Al-4V triply periodic minimal surface structures for bone implants fabricated via selective laser melting [PDF]
, 2015 PublishedJournal ArticleResearch Support, Non-U.S. Gov'tTriply periodic minimal surface (TPMS) structures have already been shown to be a versatile source of biomorphic scaffold designs. Therefore, in this work, Ti-6Al-4V Gyroid and Diamond TPMS lattices
Ahmed +42 more
core +1 more source
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
Study on selective laser melting and heat treatment of Ti-6Al-4V alloy
Results in Physics, 2018 The effects of process parameters of laser additive manufacturing (laser power, scanning speed, scanning direction) and heat treatment on the microstructure and properties of Ti-6Al-4V titanium alloy forming parts were studied under coaxial powder ...
Zhechao Fan, Hongwei Feng
doaj +1 more source
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Understanding the effects of PBF process parameter interplay on Ti-6Al-4V surface properties.
PLoS ONE, 2019 Ti-6Al-4V is commonly used in orthopaedic implants, and fabrication techniques such as Powder Bed Fusion (PBF) are becoming increasingly popular for the net-shape production of such implants, as PBF allows for complex customisation and minimal material ...
Trina Majumdar +4 more
doaj +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
High-Kinetic Inductance Additive Manufactured Superconducting Microwave Cavity
, 2017 Investigations into the microwave surface impedance of superconducting resonators have led to the development of single photon counters that rely on kinetic inductance for their operation. While concurrent progress in additive manufacturing, `3D printing'
Eric T. Holland +9 more
core +1 more source
Robust Spot Melting by 3D Spot Arrangements in Electron Beam Powder Bed Fusion
Advanced Engineering Materials, EarlyView.This work proposes an approach to replace separately melted contours for spot melting in electron beam powder fusion. Adapting the spot arrangements close to the contour combined with stacking yields a comparable surface quality without the inherent challenges of separate contours, as demonstrated, by electron optical images and roughness measurements.
Tobias Kupfer +4 more
wiley +1 more source
Mechanical properties of TiB/Ti-6Al-4V alloy composites fabricated by spark plasma sintering
Mechanical Engineering Journal, 2017 Ti-6Al-4V alloy exhibits a good combination of excellent properties, such as high specific strength, high fatigue strength, good ductility and weldability. However, Ti-6Al-4V alloy shows low stiffness and poor wear resistance.
Hiroshi IZUI, Tsubasa SHINOHARA
doaj +1 more source
Effect of Thermal Treatment of Biomedical Ti-6Al-4V Alloy on Corrosion Resistance in Simulated Physiological Solutions [PDF]
Archives of Metallurgy and Materials, 2020 The effect of heat treatment on the corrosion resistance of Ti-6Al-4V alloy was investigated in the artificial saliva solution (MAS). It has been revealed that the thermal annealing treatment temperature favors the cathodic reactions and reduce the ...
J. Ryba +3 more
doaj +1 more source