Results 11 to 20 of about 328,104 (229)
Effects of metal particles on cold spray deposition onto Ti-6Al-4V alloy via Abaqus/Explicit [PDF]
Журнал інженерних наук, 2020 Titanium alloy is the main structural material of the aerospace system component. About 75 % of titanium and titanium alloys in the world are used in the aerospace industry.
Hu W. J.
doaj +1 more source
Micromachines, 2023 TiAlN-coated carbide tools have been used to machine Ti-6Al-4V alloys in aviation workshops. However, the effect of TiAlN coating on surface morphology and tool wear in the processing of Ti-6Al-4V alloys under various cooling conditions has not been ...
Jinfu Zhao +10 more
doaj +1 more source
Effect of Tricalcium Magnesium Silicate Coating on the Electrochemical and Biological Behavior of Ti-6Al-4V Alloys. [PDF]
PLoS ONE, 2015 In the current study, a sol-gel-synthesized tricalcium magnesium silicate powder was coated on Ti-6Al-4V alloys using plasma spray method. Composition of feed powder was evaluated by X-ray diffraction technique before and after the coating process ...
Hossein Maleki-Ghaleh +6 more
doaj +1 more source
Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy [PDF]
, 2015 A significant improvement of tribological properties on Ti–6Al–4V has been achieved by developed in this study multilayer treatment method for the titanium alloys.
Mathia, T.G. +7 more
core +1 more source
Controlling the interstitial element concentration in Ti-6Al-4V using calciothermic reduction [PDF]
, 2013 The production of Ti-6Al-4V components via powder metallurgy routes is looked upon as an efficient production method that reduces wastage, but leaves finished products with high interstitial oxygen concentrations that do not meet industrial standards ...
Moorhouse, Benjamin
core +1 more source
Dry drilling of alloy Ti–6Al–4V [PDF]
International Journal of Machine Tools and Manufacture, 2005 This work is focused on the combined study of the evolution of tool wear, quality of machined holes and surface integrity of work-piece, in the dry drilling of alloy Ti–6Al–4V. Tool wear was studied with optical microscope and SEM–EDS techniques. The quality of machined holes was estimated in terms of geometrical accuracy and burr formation.
Cantero Guisández, José Luis +4 more
openaire +2 more sources
FEM analysis to optimally design end mill cutters for milling of Ti-6Al-4V [PDF]
, 2014 This paper presents an FEM analysis conducted for optimally designing end mill cutters through verifying the cutting tool forces and stresses for milling Titanium alloy Ti-6Al-4V.
Kumar, V +6 more
core +1 more source
Effect of Substrate Heating Strategy on Laser Directed Energy Deposited Ti-6Al-4V
, 2022 Three substrate heating strategies have been applied to the laser directed energy deposition of Ti-6Al-4V. From experimental and numerical studies on the effects of substrate heating strategies on the in-situ temperature profile, residual stress ...
JIEXIONG WANG (14130414)
core +1 more source
Acta Orthopaedica et Traumatologica Turcica, 2020 Objective: The aim of this study was to evaluate the mode of failure and biomechanical characteristics of Ti-6Al-4V anchors biomimetically coated with calcium phosphate (CaP) for soft tissue fixation to bone in an animal model.
Hasan Havitcioglu +5 more
doaj +1 more source
Formation of Diffusion Layer on Ti-6Al-4V Alloy during Longtime Friction with Al
Metals, 2019 Elements’ diffusion between Ti-6Al-4V alloy and Al in the process of sliding was investigated from 400 °C to 600 °C. The results showed that the atoms were diffused at the Ti-6Al-4V/Al interface.
Ruoyu Liu +6 more
doaj +1 more source