Results 11 to 20 of about 5,139 (184)
Effect of Y alloying on microstructure and mechanical properties of as-annealed Ti6Al4V alloys
Journal of Materials Research and TechnologyThe Ti6Al4V alloy with Y used as the deoxidizer contains a certain amount of Y. In this study, the effects of Y on the mechanical properties of the Ti6Al4V alloy were investigated.
Li-na Jiao +5 more
doaj +2 more sources
Coatings, 2023 In this paper, we present the mechanisms of premature fracture of modular neck stems in two case studies: (I) when the neck and stem are both made of the same Ti6Al4V alloy, and (II) when the neck and stem are made from two different alloys, CoCrMo and Ti6Al4V alloy. Our study integrates two orthopedic patients who have undergone primary uncemented THA
Drago Dolinar +10 more
openaire +3 more sources
Machinability of titanium alloys (Ti6Al4V and Ti555.3) [PDF]
Journal of Materials Processing Technology, 2009 Abstract Near-beta titanium alloys like Ti555.3 are increasingly being used in aeronautics replacing in some critical applications the most common Ti6Al4V. However, these near-beta titanium alloys have a poor machinability rating which needs to be overcome so as to maintain at least the same productivity levels as in Ti6Al4V. This paper presents the
Arrazola, Pedro-Jose +5 more
openaire +2 more sources
Abrasive Machining of Ti6Al4V Alloy [PDF]
Manufacturing Technology, 2015 This paper deals with evaluation of ground surface of Ti6Al4V alloy according to surface roughness. This titanium alloy has large scale of utilization, it is used for implants and surgical instruments. Significant problem during grinding of titanium alloys is generation of large amount of heat which can cause surface cracks, increase hardness of ...
Radek Lattner +3 more
openaire +1 more source
Influence of Material Microstructures in Micromilling of Ti6Al4V Alloy [PDF]
Materials, 2013 In the most recent decades the introduction of unconventional machining processes allowed the development of micromachining techniques. In this work, the influence of material microstructures on the micromilling process was investigated. Ti6Al4V alloy was selected as workpiece material since it is a very common material for micro applications and ...
ATTANASIO, Aldo +4 more
openaire +3 more sources
Open Engineering, 2022 The corrosion polarization behavior of 439ll ferritic (439ll), 316L austenitic (316L), and NO7208 nickel-chromium-aluminum-iron (NO7208) stainless steels, and Ti6Al4V titanium (Ti6Al4V) alloys was studied in 4 M H2SO4 + 5% NaCl solution at 35 and 70°C ...
Loto Roland Tolulope
doaj +1 more source
Metals, 2023 TiC/graphene/Ti6Al4V composites were prepared by laser powder bed fusion using graphene and Ti6Al4V powder. The differences in microstructure and high-temperature mechanical properties between the Ti6Al4V alloy and the TiC/graphene/Ti6Al4V composite were
Shijie Chang +3 more
doaj +1 more source
Assessment of Ti6Al4V alloy fatigue properties based on specimens produced by DMLS technology [PDF]
MATEC Web of Conferences, 2021 The Ti6Al4V alloy produced by additive methods is the most studied material, which can be attributed to its wide application and the resulting need for a thorough understanding of this material and its behavior under static and fatigue loads.
Karolewska Karolina
doaj +1 more source
Frontiers in Bioengineering and Biotechnology, 2023 Introduction: Ti6Al4V titanium alloy is widely used in producing orthopedic and maxillofacial implants, but drawbacks include high elastic modulus, poor osseointegration performance, and toxic elements.
Jiantao Liu +9 more
doaj +1 more source
Laser Surface Modification of Ti6Al4V-Cu for Improved Microhardness and Wear Resistance Properties [PDF]
Materials Research, 2017 To modify the properties of Ti6Al4V alloy, Cu has been added to host an antimicrobial effect in the revised alloy for marine application. The Laser Metal Deposition (LMD) process on the Ti6Al4V alloy and Cu was been investigated for surface modification ...
Mutiu Folorunsho Erinosho +3 more
doaj +1 more source