Results 11 to 20 of about 1,708 (185)
Journal of Materials Research and Technology, 2022 This paper presents a novel process for preparation of TiB2 coatings, which is a combination of synthesis of TiB2 nanoparticles by borothermal reduction of TiO2 in molten NaCl–KCl–AlF3 system and subsequent electrophoretic deposition of the as ...
Jun Zhang +5 more
doaj +2 more sources
Chinese Journal of Aeronautics, 2021 Abstract In-situ ceramics particle reinforced aluminum matrix composites are favored in the aerospace industry due to excellent properties. However, the hard ceramic particles as the reinforcement phase bring challenges to machining. To study the effect of in-situ TiB2 particles on machinability and surface integrity of TiB2/2024 composite and TiB2 ...
Jie CHEN +8 more
openaire +1 more source
Microstructure features and mechanical properties of non-heat treated HPDC Al9Si0.6Mn–TiB2 alloys
Journal of Materials Research and Technology, 2023 This study aimed to enhance the mechanical properties of high pressure die casting (HPDC) Al9Si0.6Mn alloys by incorporating in-situ TiB2 particles. The effects of TiB2 addition on the microstructure and mechanical properties of as-HPDC Al9Si0.6Mn alloys
Chengyang Hu +8 more
doaj +1 more source
Isothermal section of the Ti-Si-B system at 1250 ° C in the Ti-TiSi2-TiB2 region [PDF]
Materials Research, 2013 A partial isothermal section (Ti-TiSi2-TiB2 region) of the ternary Ti-Si-B system at 1250 ° C was determined from heat-treated alloys prepared via arc melting.
Alfeu Saraiva Ramos +5 more
doaj +1 more source
Journal of Materials Research and Technology, 2023 Grain size, grain orientation, the size and distribution of the precipitated phases are very important for the mechanical properties of particle reinforced aluminum matrix alloys.
Daoxiu Li +6 more
doaj +1 more source
Advanced heat treated die-cast aluminium composites fabricated by TiB2 nanoparticle implantation
Materials & Design, 2020 The global carbon emission reduction strongly requires high strength lightweight die-cast aluminium alloys in industry. Here die-cast AlSiMgMn–TiB2 composites with advanced mechanical performance were fabricated by the implantation of TiB2 nanoparticles.
Xixi Dong +5 more
doaj +1 more source
High Temperature Materials and Processes, 2015 In this study, microstructural, mechanical and wear properties of TiB2 reinforced Al 2014-based composites produced by vacuum infiltration were investigated under different production temperatures.
Araz Şule Ocak +4 more
doaj +1 more source
Molten salt synthesis of TiB2 nanopowder by reduction of TiO2 with MgB2 [PDF]
Processing and Application of Ceramics, 2021 This research work presents the preparation of TiB2 nanopowders by molten-salt synthesis (MSS) technique from TiO2 and MgB2 as starting active materials and MgCl2 as a molten salt.
Shah Liaqat Ali
doaj +1 more source
Machining Investigations of Squeeze Cast TiB2/Al 7075 Composites through EDM: Regression Modelling and Weighted Principal Component Analysis [PDF]
Archives of Metallurgy and Materials, 2023 2 wt.% TiB2 (mean particle size: 400 nm) reinforced Al 7075 metal matrix composites (MMCs) fabricated through mechanical stirring and ultrasonic agitation integrated squeeze casting process were subjected to electrical discharge machining (EDM) after ...
Rahul Chandra Pradhan +5 more
doaj +1 more source
The Influence of TiB2 Particle on the Mechanical Property of Cu-TiB2 Composites [PDF]
Korean Journal of Materials Research, 2004 The mechanical and electrical properties of composites prepared by hot extrusion and cold drawing according to the variation of contents and the size of particle have been studied. The experimental results showed that the electrical conductivity was decreased with increasing the content, and their tensile strength and hardness increased inversely.
openaire +1 more source