Results 31 to 40 of about 1,708 (185)
Flexibilizing inorganic thermoelectrics
FlexMat, EarlyView.This perspective reviews advances in flexible inorganic thermoelectric materials, covering ductile bulks, thin films, and fibers/yarns. It highlights strategies like warm metalworking, van der Waals material screening, orientation and sandwich engineering, and device integration, offering pathways to combine flexibility and performance for wearable ...
Xiao‐Lei Shi +3 more
wiley +1 more source
Laser Powder Bed Fusion of Alumina: Effects of Scanning Strategies on External and Internal Defects
Advanced Engineering Materials, Volume 28, Issue 14, 22 July 2026.This study investigates how scanning strategies affect pure alumina in laser powder bed fusion. Linear 45° scanning yields uniform surfaces but high porosity, while the island‐concentric strategy provides higher density with through‐holes favorable for infiltration. Findings highlight pathways toward optimizing defect‐free alumina parts.
Mohamed Abdelmoula +7 more
wiley +1 more source
The characteristics of wear resistance of Cu-TiB2 composites reinforced by TiB2 powders [PDF]
Korean Journal of Materials Research, 2005 In this study the effect of the content of on wear properties was investigated. composites have been fabricated by hot extrusion. Sliding wear tests were peformed by a pin-on-disk type wear test machine under dry condition and loads varied with from 20N to 80N at sliding speed 3.5Hz.
openaire +1 more source
Fabrication of reaction bonded TiB2/Si/SiC composites for thermal applications
International Journal of Ceramic Engineering & Science, 2020 Titanium diboride (TiB2) is an extremely hard ceramic which has excellent heat conductivity, oxidation stability, and resistance to mechanical erosion.
Jiwen Wang +3 more
doaj +1 more source
Microstructure Engineering Toward High Cost‐Effective Nd–Fe–B Sintered Magnets: A Review
Rare Metals, Volume 45, Issue 7, July 2026.ABSTRACT Nd–Fe–B sintered magnets, critical for enhancing electromechanical conversion efficiency and operational stability in wind turbines and electric vehicle drives, are prized for their outstanding coercivity, high remanence, and superior maximum energy product.
Dongmin Zhang +5 more
wiley +1 more source
Hittite Journal of Science and Engineering, 2021 In this study; Hybrid composites containing different proportions of TiB2 and graphene were produced using the pressure infiltration method. Inert SF6 gas is used to prevent oxidation in the productions.
Muhammet Turan +3 more
doaj +1 more source
Rare Metals, Volume 45, Issue 7, July 2026.ABSTRACT High‐strength aluminum (Al) alloys are usually unprintable by laser powder bed fusion (LPBF) due to the severe hot cracking along the columnar grains. Doping elements scandium (Sc) and/or zirconium (Zr) is an effective way to eliminate hot cracks by refining the grain size to nearly nanoscale levels.
Zehuan Zhang +15 more
wiley +1 more source
Advanced Functional Materials, Volume 36, Issue 52, 29 June 2026.Cyclic unloading‐aging‐reloading micro‐tensile tests under various aging durations and temperatures, combined with comprehensive microstructural characterization reveal that the yield point phenomenon in Aluminum‐Carbon (Al‐C) thin films originates from Cottrell atmosphere formation.
Zion Lee +10 more
wiley +1 more source
cMat, Volume 3, Issue 2, June 2026.ABSTRACT To address the critical challenge of poor interfacial compatibility and the difficulty of synergistically enhancing electrical/thermal conductivity and mechanical properties in copper–graphene composites, this study proposes a novel cobalt‐mediated interfacial engineering strategy.
Shijian Li +9 more
wiley +1 more source
Journal of Materials Research and Technology316L stainless steel is used in a wide variety of corrosion-prone locations. However, its low hardness and poor tribological properties limit its application under heavy wear conditions.
Zhongxin Wang +8 more
doaj +1 more source