Results 91 to 100 of about 18,782 (207)

Comparison of empirical and predicted substrate temperature during surface melting of microalloyed steel using TIG technique and considering three shielding gases [PDF]

, 2019
Erosion and wear resistance of steel can be enhanced by incorporating a ceramic powder in the surface. This aspect of surface engineering has applications in areas such as mining, agriculture and transport.
Baker, T. N., Mridha, S., Munoz-Escalona, P., Ogwu, A., Walker, A.   +4 more
core   +3 more sources

Helium additions to MIG shielding gas - an economic option? [PDF]

, 2011
An investigation has been carried out to establish the technical and economic benefits of adding two levels of helium to a normal shielding gas. Technically no adverse issues were established using the two levels of helium, and the most significant ...
Galloway, Alexander, Gillies, Andrew, McPherson, Norman   +2 more
core  

Enhancing Welding Productivity and Mitigation of Distortion in Dissimilar Welding of Ferritic-Martensitic Steel and Austenitic Stainless Steel Using Robotic A-TIG Welding Process

Journal of Manufacturing and Materials Processing
The P91 martensitic steel and 304L austenitic stainless steels are two mainly used structural steels in power plants. The major problem in conventional multipass tungsten inert gas (TIG) welding of P91/304L steel is high heat input and joint distortion ...
Tushar Sonar, Mikhail Ivanov, Igor Shcherbakov, Evgeny Trofimov, Emiliya Khasanova, Muralimohan Cheepu, Kun Liu   +6 more
doaj   +1 more source

Verification of heat treatment on properties of progresive heat resisting steels [PDF]

, 2009
Předmětem diplomové práce je zkouška postupu svařování žáropevné oceli T24 metodou TIG. V praxi se jedná o spojování membránových stěn při stavbě parních elektrárenských kotlů.
Volf, Ondřej
core  

A comparative study of electrochemical corrosion behavior in Laser and TIG welded Ti–5Al–2.5Sn alloy

Journal of Materials Research and Technology, 2019
Corrosion behavior of TIG and laser welded Ti–5Al–2.5Sn alloy was compared using different electrochemical techniques. Bead on plate (BoP) configuration was used for welding of 1.6 mm thick Ti–5Al–2.5Sn plates which led to the formation of complete α ...
Muhammad Shamir, Massab Junaid, Fahd Nawaz Khan, Aqeel Ahmad Taimoor, Mirza Nadeem Baig   +4 more
doaj   +1 more source

Sistem Kontrol Jaringan Syaraf Tiruan Berbasis Simulasi Pada Pengelasan Pipa Aluminum [PDF]

, 2011
Dalam penelitian ini telah dikembangkan sistem pengelasan otomatis Tungsten Inert Gas (TIG) dengan menggunakan sensor vision pada pengelasan pipa aluminum.
Baskoro, A. S. (Ario), Kabutomori, M. (Masashi), Suga, Y. (Yasuo)   +2 more
core  

Research on TIG Welding Technology for Stainless Steel Rail Vehicle Underframes

Chengshi guidao jiaotong yanjiu
ObjectiveA rubber seat must be attached to the troughs of the corrugated plates on stainless steel rail vehicle underframes. Therefore, it is required that the corrugated plate welding should not form excess weld metal like other arc welding methods.
Liqi KANG, Meng GUO, Chengfei WANG, Yanan WANG, Haiwei LIU, Ya GAO   +5 more
doaj   +1 more source

Influence of Pulsed Arc Parameters on the Tig Welding Process for the Stainless Steel Duplex UNS S31803. [PDF]

Materials (Basel), 2023
Generoso VMA, Souza LM, Pereira EC, Monteiro SN, de Azevedo ARG.   +4 more
europepmc   +1 more source

Study on Arc Welding Seam Tracking of TIG Welding

IOP Conference Series: Earth and Environmental Science, 2018
In this paper, the welding seam tracking system based on rotating arc TIG welding is studied. The design of pid controller for the hardware, software, signal acquisition, filtering and weld deviation identification of the system is deeply studied. And the conclusion is obtained, which lays a foundation for the tracking of rotating arc weld in TIG ...
Jin Wei, Xia Xiang
openaire   +1 more source

Characterization of an energy efficient pulsed current TIG welding process on AISI 316 and 304 stainless steels. [PDF]

Heliyon, 2023
Casanueva R, Brañas C, Diaz FJ, Azcondo FJ, Ferreño D, Setien J.   +5 more
europepmc   +1 more source