Results 141 to 150 of about 258,109 (284)

Advancing Research on Biomaterials and Biological Materials with Scanning Electron Microscopy under Environmental and Low Vacuum Conditions

Advanced Engineering Materials, EarlyView.
Herein, environmental scanning electron microscopy (ESEM) is discussed as a powerful extension of conventional SEM for life sciences. By combining high‐resolution imaging with variable pressure and humidity, ESEM allows the analysis of untreated biological materials, supports in situ monitoring of hydration‐driven changes, and advances the functional ...
Jendrian Riedel, Lea Dierker, Antoine Eyram Kwame, Kim Nora Wagner, Jonas J. Unterholzner, Jan‐Henning Dirks, Dorothea Brüggemann   +6 more
wiley   +1 more source

Comparison of Different Head Tilt Angles in Tomotherapy and Volumetric Modulated Arc Therapy for Hippocampal-Avoidance Whole-Brain Radiotherapy

Technology in Cancer Research & Treatment
Purpose Hippocampal-avoidance whole-brain radiotherapy (HA-WBRT) planning can present challenges. This study examines the influence of head tilt angles on the dosimetric characteristics of target and organs at risk (OARs), aiming to identify the optimal ...
Yang Li MS, Cuiyun Yuan MS, Dongjie Chen MD, Sisi Xu MD, Wei Jiang MD, Jiaxin Huang BS, Shanshan Ye BS, Yin Zhang MS, Jun Liang MD, Chenbin Liu PhD   +9 more
doaj   +1 more source

Introduction of a New Radiographic Parameter to Predict Proximal Junctional Kyphosis in Adult Spinal Deformity: UIVPTA (Uppermost Instrumented Vertebra-Pelvic Tilt Angle). [PDF]

Neurospine, 2023
Park SJ, Lee CS, Park JS, Shin TS.
europepmc   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Evaluation of lateral and anterior center-edge angles according to sex and anterior pelvic plane tilt angle: a three-dimensional quantitative analysis. [PDF]

J Orthop Surg Res, 2023
Hong KB, Lee WS, Kang K, Kang KT, Cho BW.   +4 more
europepmc   +1 more source

Laser Metal Deposition of Aluminum Alloys 7075 and 5083 with the Addition of Volatile Alloying Elements through Powder Blending

Advanced Engineering Materials, EarlyView.
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen, Anastasiya Toenjes, Annika Bohlen, Thomas Seefeld   +3 more
wiley   +1 more source

Modeling and estimation of the optimal tilt angle, maximum incident solar radiation, and global radiation index of the photovoltaic system. [PDF]

Heliyon, 2022
Obiwulu AU, Erusiafe N, Olopade MA, Nwokolo SC.   +3 more
europepmc   +1 more source

Manufacturing Continuous Fiber‐Reinforced Printing Filaments: Development of a Post‐Consolidation Unit

Advanced Engineering Materials, EarlyView.
A novel, temperature‐controlled post‐consolidation unit is developed to test its potential to improve the melt impregnation process used to manufacture continuous fiber‐reinforced filaments for additive manufacturing of high‐performance thermoplastics.
Daniel Beermann, Patrick Schiebel, David May   +2 more
wiley   +1 more source

The Forward and Lateral Tilt Angle of the Neck and Trunk Measured by Three-Dimensional Gait and Motion Analysis as a Candidate for a Severity Index in Patients with Parkinson's Disease. [PDF]

Neurol Int, 2022
Matsumoto H, Shiraishi M, Higashi A, Hino S, Kaburagi M, Mizukami H, Maki F, Yamauchi J, Tanabe K, Sato T, Yamano Y.   +10 more
europepmc   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source