Results 121 to 130 of about 61,426 (293)

Interfacial microstructure and shear strength of Ti-6Al-4V/TiAl laminate composite sheet fabricated by hot packed rolling

, 2011
A two layer Ti-6Al-4V(wt%)/Ti-43Al-9V-Y(at%) laminate composite sheet with a uniform interfacial microstructure and no discernible defects at the interfaces has been prepared by hot-pack rolling, and its interfacial microstructure and shear strength were
Chen, Yuyong, Yuyong Chen, Kong, Fantao, Fantao Kong, Deliang Zhang, Zhang, Deliang   +5 more
core   +1 more source

3D Printing Innovations in Polymeric Porous and Patterned Architecture

Advanced Functional Materials, EarlyView.
Polymeric foams occupy a unique structural space between dense solids and open networks, where engineered void fraction governs mechanical compliance, thermal resistance, and mass transport. Additive manufacturing now enables precise spatial control over cellular architecture, unlocking designer foam structures across applications spanning crash ...
Dhanush Patil, Sri Vaishnavi Thummalapalli, Clarissa Westover, Arunachalam Ramanathan, M. Taylor Sobzcak, Roumika Patil, Qixuan Xiang, Tiantian Li, Sui Yang, Timothy E. Long, Hongyue Sun, Xianqiao Wang, Yang Liu, Kenan Song   +13 more
wiley   +1 more source

Analysis of ignition resistance performance and mechanism of TA7 and TC11 titanium alloys under impact-grinding conditions

Journal of Aeronautical Materials
A titanium alloy collision friction ignition device was used to conduct collision and continuous friction between TC4 titanium alloy rotating rod and TA7 and other titanium alloy collision samples.Combined with SEM and other microscopic analysis，the anti-
SHI Lin, JIA Leiting, GUO Hongbo, PENG Hui   +3 more
doaj   +1 more source

The Formulation of Titanium - based Metal Feedstocks and the Fabrication of Parts using the Powder Injection Moulding Process

, 2015
Development of a profitable titanium industry for New Zealand will not come about without innovative technologies. Plastic injection moulding has long held a place in NZ manufacturing to produce large quantities of complex parts and holds the key to such
Ewart, Paul Douglas
core  

In Situ Crystalline‐Amorphous Composite Oxide Structure Suppressing Thermal Wear Instability for Refractory Multi‐Principal Element Alloy

Advanced Functional Materials, EarlyView.
An effective strategy is developed to overcome the medium temperatures wear resistance degradation in refractory multi‐principal element alloys. By utilizing chemical short‐range ordering to trigger oxygen‐induced amorphization, a composite oxide structure is formed, which combines high hardness with robust stiffness.
Xuhui Pei, Jianbao Zhang, Hanming Wang, Yin Du, Tao Yang, Ji‐Jung Kai, Benyebka Bou‐Saïd, Haifeng Wang   +7 more
wiley   +1 more source

Design and Rate Control of Large Titanium Alloy Springs for Aerospace Applications

Aerospace
During the separation between satellite and launch vehicles, large steel springs are often used as compression separation spring sets in a catapult separation system. Replacing the steel springs with titanium alloy springs could reduce weight by about 50%
Lei Li, Qiufa Xu, Haiying Yang, Yang Ying, Zuhan Cao, Dizi Guo, Vincent Ji   +6 more
doaj   +1 more source

Laser surface modification of Ti alloys

, 2010
The laser surface engineering of titanium alloys has been developed over the past 30 years to produce a modified layer up to 1mm depth, thicker than alternative techniques.
Baker, T.N.
core  

Designed Lewis Acid–Base Passivation for High Performance Perovskite Solar Cells

Advanced Functional Materials, EarlyView.
ABSTRACT Silicon's high cost and long energy payback time remain major barriers to the global expansion of solar power. In contrast, metal–halide perovskites offer abundant, solution‐processable absorbers, and have achieved efficiencies of 25%–30%, positioning them as strong competitors to silicon.
Afna Manaf, Hiba Shahulhameed, Bhabani Sankar Swain, Shengzhong (Frank) Liu, Adel Najar   +4 more
wiley   +1 more source

Investigation of methods to manipulate geometry, microstructure and mechanical properties in titanium large scale Wire+Arc Additive Manufacturing [PDF]

, 2014
Wire+arc additive manufacturing is a technique suitable for the deposition of large components; a variety of materials can be processed, including titanium.
Martina, Filomeno
core  

Unlocking Exceptional Strengthening in Aluminum Alloys via Interstitial Cottrell Atmosphere Formation

Advanced Functional Materials, EarlyView.
Cyclic unloading‐aging‐reloading micro‐tensile tests under various aging durations and temperatures, combined with comprehensive microstructural characterization reveal that the yield point phenomenon in Aluminum‐Carbon (Al‐C) thin films originates from Cottrell atmosphere formation.
Zion Lee, Hojang Kim, Yixuan Hu, Injong Oh, Tae‐Hyeok Kang, Hyeonbeen Noh, Yuhyun Park, Sunkun Choi, Pyuck‐Pa Choi, Kolan Madhav Reddy, Gi‐Dong Sim   +10 more
wiley   +1 more source