Results 61 to 70 of about 130,653 (303)
Toward a better understanding of tool wear effect through a comparison between experiments and SPH numerical modelling of machining hard materials [PDF]
, 2009 The aim of this study is to improve the general understanding of tungsten carbide (WC–Co) tool wear under dry machining of the hard-to-cut titanium alloy Ti6Al4V. The chosen approach includes experimental and numerical tests.
Bil +26 more
core +7 more sources
Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
Journal of Materials Research and TechnologyTitanium alloys, especially α+β type ones, are usually subjected to diverse heat treatments for tailoring their microstructures and mechanical properties.
Mingbing Li +6 more
doaj +1 more source
Stress corrosion cracking of titanium alloys - Potential transients at open circuit during SCC and pitting corrosion, and chloride absorption during formation of TiO sub 2 Quarterly progress report, Jul. 1 - 30 Sep. 1967 [PDF]
Stress corrosion cracking of titanium alloys and chloride absorption during formation of titanium ...
Beck, T. R.
core +1 more source
On the Choice of Tool Material in Friction Stir Welding of Titanium Alloys [PDF]
, 2012 Friction Stir Welding (FSW) is a solid state welding process patented in 1991 by TWI; initially adopted to weld aluminum alloys, is now being successfully used also for magnesium alloys, copper and steels.
Buffa, G. +3 more
core
Advanced Engineering Materials, EarlyView.Through direct application of porous transport layer (PTL) on the bipolar plate (BPP) with thermal spraying, the interfacial contact resistance is improved. With the cold gas sprayed BPP–PTL coating system, a proton exchange membrane water electrolysis cell with a cell voltage of Ucell = 1.9 V can be operated up to i = 2.5 A/cm2 in a dynamic mode ...
Kirsten Bobzin +5 more
wiley +1 more source
Metals, 2015 Although originally discovered in the 18th century [1], the titanium industry did not experience any significant advancement until the middle of the 20th century through the development of the gas turbine engine [2]. Since then, the aerospace sector has dominated worldwide titanium use with applications in both engines and airframe structures [3 ...
openaire +2 more sources
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
Irradiation effect at cryogenic temperature on tensile properties of titanium and titanium- base alloys [PDF]
Irradiation effects on tensile behavior of titanium alloys and titanium at cryogenic ...
Haley, F. A., Younger, C. L.
core +1 more source