Results 71 to 80 of about 3,572 (225)
Numerical study of crucial parameters in tilt casting for titanium aluminides [PDF]
China Foundry, 2011 Numerical modeling of the tilt casting process for TiAl alloys was investigated to achieve a tranquil mould filling and TiAl castings free of defects.
Hong Wang +2 more
doaj
Engineering Reports, Volume 6, Issue 12, December 2024.The graphical abstract demonstrates that adding 9 wt% nickel to an Al‐Si matrix composite increases hardness by 25.93%, tensile strength by 40.3%, and density by 6.01%, but decreases impact strength by 50% compared to the A413 alloy. It includes SEM images, a stir casting schematic, and data on tensile and impact behavior.
A. Saiyathibrahim +3 more
wiley +1 more source
First Principles Study of Bonding Mechanisms at the TiAl/TiO2 Interface
Metals, 2020 The adhesion properties of the TiAl/TiO2 interface are estimated in dependence on interfacial layer composition and contact configuration using the projector augmented wave method.
Alexander V. Bakulin +4 more
doaj +1 more source
Регулирование структуры и фазового состава алюминидов титана, полученных зонной плавкой [PDF]
, 2017 Разработана технология, в едином процессе объединяющая индукционную зонную плавку интерметаллида системы TiAl с последующей термической обработкой, обеспечивающей скорость охлаждения, которая способствует гомогенизации структуры и механических ...
Аснис, Е.А. +7 more
core +1 more source
Materials and Corrosion, Volume 75, Issue 12, Page 1583-1599, December 2024.Hot corrosion is encountered in turbine engines, where Co‐based superalloys are proposed to replace Ni‐based materials. In the present study, the hot corrosion resistance of γ/γ′ superalloys of the Co–Ni–Al–W alloys was increased by their Co and W content.
Till König +3 more
wiley +1 more source
Journal of Advanced Materials in Engineering, 2015 In recent years, much research has been performed in the field of nanomaterials synthesis using mechanochemical process. In this research, TixAly/Al2O3 ceramic matrix nanocomposite was produced by the mechanochemical method.
m.godarzi, A. Saidi
doaj
Cost benefit study of advanced materials technology for aircraft turbine engines [PDF]
The cost/benefits of eight advanced materials technologies were evaluated for two aircraft missions. The overall study was based on a time frame of commercial engine use of the advanced material technologies by 1985.
Hillery, R. V., Johnston, R. P.
core +1 more source
Short Term Oxidation of a Ti-46Al-8Nb Alloy at 700°C in Air [PDF]
, 2010 Thermogravimetry was used to study the oxidation behaviour of a lamellar Ti46Al8Nb alloy during holding at 700°C in synthetic air. A parabolic plot of the oxidation kinetics shows three different regimes over the total duration (50 h) of the tests ...
Lacaze, Jacques +4 more
core +1 more source
Knudsen effusion mass spectrometry: Current and future approaches
Rapid Communications in Mass Spectrometry, Volume 38, Issue 14, 30 July 2024.Rationale Knudsen effusion mass spectrometry (KEMS) has been a powerful tool in physical chemistry since 1954. There are many excellent reviews of the basic principles of KEMS in the literature. In this review, we focus on the current status and potential growth areas for this instrumental technique.
Nathan S. Jacobson +4 more
wiley +1 more source
Advanced Engineering Materials, Volume 26, Issue 14, July 2024.Powder hot extrusion and heat treatment of titanium metal matrix composite's lead to high specific stiffnesses of 34.6 GPa cm3 g−1. Remelting, to simulate an additive manufacturing method, of these materials results in severe changes of the microstructure and a decrease in the mechanical properties even with ex situ reinforcements. Titanium alloys with
Nico Moser +7 more
wiley +1 more source