Results 31 to 40 of about 42,769 (264)
Advanced Engineering Materials, EarlyView.This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig +2 more
wiley +1 more source
One-Piece Titanium Implants: Retrospective Case Series
Case Reports in Dentistry, 2021 Purpose. One-piece titanium implants are not routinely used for reconstruction after tooth loss. Several limitations seemed to be apparent although the concept provides a straightforward approach for different clinical situations.
Gunar Wagner, Dieter Hartung
doaj +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
The connective tissue response to Ti, NiCr and AgPd alloys.
Folia Histochemica et Cytobiologica, 2010 The aim of the study was to compare the connective tissue response of Lewis rats to Ti, NiCr and AgPd alloys. It was found that implants were covered by collagen-rich, well vascularized capsules. Titanium was covered by the thinnest capsule (57 Âą 20 Îźm)
Jerzy Sokołowski +3 more
doaj +1 more source
Frontiers in Bioengineering and Biotechnology, 2021 Percutaneous implants are widely used in clinical practice. However, infection is the main clinical problem of percutaneous implants. Titanium dioxide nanotubes are suitable for forming coatings on complex surfaces such as implants.
Qiang Miao +11 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
Numerical investigation of the optimal porosity of titanium foam for dental implants
HeliyonBackground: This paper aims to indicate numerically the accurate porosity used for dental implants, following the emphasis on the preference for titanium foam on pure titanium implants.
Hussein Farroukh +2 more
doaj +1 more source
Atomically Resolved Interfacial Analysis of Bone‐Like Hydroxyapatite Nanoparticles on Titanium
Advanced NanoBiomed Research, 2023 Titanium is commonly used for medical devices, including osseointegrating implants, owing to its biocompatibility and mechanical properties. Nanostructuring titanium implants is known to enhance the healing process by promoting bone growth on the implant
Gustav Eriksson +3 more
doaj +1 more source
Titanium as a Biomaterial for Implants [PDF]
, 2012 Se espera que un biomaterial ideal exhiba propiedades como una biocompatibilidad muy alta, es decir, sin respuesta tisular adversa. Además, debe tener una densidad tan baja como la del hueso, alta resistencia mecánica y resistencia a la fatiga, bajo módulo elástico y buena resistencia al desgaste.
Carlos Oldani, Alejandro Domínguez
openaire +1 more source
Advanced Engineering Materials, EarlyView.A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt +4 more
wiley +1 more source